I may have damaged my 54 caliber percussion Lyman GPR barrel. Does anyone know where I can get a replacement barrel?
Thank you in advance.
Thank you in advance.
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Damaged GPR barrel
- Thread starter Flint-Hunter
- Start date
Help Support Muzzleloading Forum:
- Joined
- Jan 31, 2009
- Messages
- 13,034
- Reaction score
- 7,293
Getting a new barrel with rifling of your choice put together using the GPR plug and hardware is an easy path forward. Having the existing barrel rebored or relined is doable too.
How you possibly damaged the barrel will determine what route is the best to take, a rebore will cost you about $140, a re-line a good bit more.
I thought I did the same when I fired my rifle with 90gr of 2F pushing a short-started ball, I was sure I had to bulge the barrel but alas, the barrel was unscathed. The bad thing is I did it a second time a year or so later, again with no damage.
These folk claim to have new barrels, I have done business with them before.
https://www.midsouthshooterssupply.com/dept/muzzleloaders/parts/barrels
I thought I did the same when I fired my rifle with 90gr of 2F pushing a short-started ball, I was sure I had to bulge the barrel but alas, the barrel was unscathed. The bad thing is I did it a second time a year or so later, again with no damage.
These folk claim to have new barrels, I have done business with them before.
https://www.midsouthshooterssupply.com/dept/muzzleloaders/parts/barrels
Last edited:
I’m not sure exactly how I damaged the barrel. I’ve had the gun for 15 years and have gone shooting countless times, and have always cleaned it thoroughly later the same day with warm water, then dry it, and then coat with WD-40. When I grabbed the previously cleaned gun yesterday and dropped a 54 ball down the barrel it didn’t bounce at the bottom like normal. I cleaned the already “clean” gun and found the last 5 inches of travel (near the breach) was rough. I’m guessing I didn’t remove all the water after the previous cleaning. If that wasn’t the cause, then I don’t know what happened.
@Flint-Hunter, at this time, you have little to lose but a bit of elbow grease and some time.
Get a 50 caliber jag, some green or maroon Scotch Brite pad and a sturdy working rod. Use a small square of the pad to smooth out that 5" of barrel as best you can. This will probably take several hundred strokes and several pads to get the barrel smoother. It will probably shoot acceptably well.
In the future, after cleaning, store the rifle muzzle down. Any remaining liquid will flow out of the breech and not settle in to harm or foul the breech.
Get a 50 caliber jag, some green or maroon Scotch Brite pad and a sturdy working rod. Use a small square of the pad to smooth out that 5" of barrel as best you can. This will probably take several hundred strokes and several pads to get the barrel smoother. It will probably shoot acceptably well.
In the future, after cleaning, store the rifle muzzle down. Any remaining liquid will flow out of the breech and not settle in to harm or foul the breech.
- Joined
- Jan 27, 2004
- Messages
- 1,715
- Reaction score
- 526
Before getting a new barrel, take it out and shoot it. If it still shoots well, forget the new barrel. I've seen barrels that look like a sewer pipe shoot great.
Agree with Waksupi.
If it requires attention, and if I cannot find a new or better barrel, I would contact Bobby Hoyt and see what he could do for it and determine if the cost is worth it.
If it requires attention, and if I cannot find a new or better barrel, I would contact Bobby Hoyt and see what he could do for it and determine if the cost is worth it.
- Joined
- Jul 8, 2019
- Messages
- 3,154
- Reaction score
- 5,655
Good information! If it is a 50 cal. he could turn it into a 54 cal. and could hunt anything that moves and have a lighter rifle to boot. I would consider it an inprovement.
I listed an unfired 54 cal GPR barrel for sale a couple of months ago. It's still available. Price is $335. Good luck finding a new one cheaper. PM me if interested.
FOR SALE - Unfired, Like New 54 cal Lyman Great Plains Barrel
Dave
FOR SALE - Unfired, Like New 54 cal Lyman Great Plains Barrel
Dave
Last edited:
Midsouth Shooters Supply has a new drop in GPR barrel for $290.
Stykbow
50 Cal.
- Joined
- Aug 2, 2021
- Messages
- 1,075
- Reaction score
- 2,526
I would add that they seem to have left hand barrels only.
I seen the problem right off---it is that stuff called WD40! It can actually cause rust but if it is not rust it is dried WD40. It will leave a build up that nothing will desolve. I have seen firing pins so frozen in they had to be pounded out and everything cleaned mechanically. The best use of that stuff is to set the cans at 100 yards and shoot at them.
WD-40, the gunsmith's friend. I earned lotsa bucks cleaning the varnish out of guns for people who used it.
- Joined
- Mar 21, 2022
- Messages
- 1,558
- Reaction score
- 1,879
Agree with the above comments on WD40. A lot of people think it is a good lube and storage oil. Not! WD40 is a solvent. It is not a lubricant. It is a short term water displacer which is a short term light grade protection for metal that has been exposed to moisture. Any firearm part that has had WD40 used on it should be thoroughly cleaned, dried, and a good coat of high grade lubricant applied as soon as possible.
Last edited:
"I seen the problem right off" sounds like the line from the movie Jeremiah Johnson. Nicely done.
Hi Dave. I'd like to purchase your barrel, but I don't know how to PM you in this forum.
-Richard
- Joined
- Mar 21, 2022
- Messages
- 1,558
- Reaction score
- 1,879
Move your cursor over the pink square with a D in it above his name. A box will appear and in it you will see a line that says "start a conversation". Click on that and it will take you into the private message format and you can start a private conversation with him.
