Fancy Wood - Making my own grips

[KingOfKindling]

So, I've got big hands, and navy sized grips really are just too small. The army grips are a bit better, and I've got a Pietta 1860 franken gun with navy grips I wanted to swap out. The triggerguard and backstrap parts were available, but no decent grips were popping up. Taylor firearms sometimes stocks raw grips, but they were out.

Figured I'd try and make my own. Could do it by hand, but I have 3D printers and a home built CNC router, and in the future I'd like to make a detachable buttstock (since they're pretty much unobtanium). Some grips seem like good practice, and my CNC machine needed maintenance. I can tune the machine, and practice cutting stuff without being out as much as a full stock.

Started out with modeling a grip in Fusion360, then 3D printing various test samples. This one is a bit early, I settled on being a bit more oversized to make sure final shaping would be as good as I can do.

First wood cuts were on a piece of curly maple board I had on the shelf. This is a 7mm 4 flute bit. Travel speed of 20 inches per minute and spinning about 20k rpm.

After the roughing was completed I did the finishing pass with a 1/16 2 flute ball end mill. Was all I had, and didn't have enough clearance so I needed to get fancy with the CAM settings. Was able to finish the grip, but the grip ended up a bit long. No big deal, I've since had some proper bits arrive. Had video of the finishing pass, but it's too big to upload apparently. Here's a picture instead.

Fit is pretty good on my test gun. This one has a factory Army grip, so it makes for a good template. More material to remove by hand than I'd like, but with some minor tweaking and the correct ball end mill the next pieces will be better.

I've got some Karelian Birch I'm playing with, and some various maple burl wood coming. Still shopping around for a nice chunk of highly figured walnut.

 

[AwwNaww]

Very impressive!

 

[KingOfKindling]

Very impressive!

Thanks. It's been working better than I expected. I thought curly wood would be giving me fits with the router bits.

Even the Karelian Birch with its crazy grain and inclusions has cut like butter. Probably the high spindle speeds I'm running. My end mill life span may be short.

Finishing with a 4 flue 1/8" ball end mill. 10% stepover, 22k RPM, and 25 inches per minute travel. Much nicer to have a bit that reaches where it needs to.

Working on some different stains right now. Using scrap to come up with various combinations to see if I can find something I like. I'll try and get pictures processed later.

I really wonder what machines they used in the Colt factory to make grips. Anyone know if there are any books out there with pictures of that kind of stuff?

 

[stubshaft]

I'd try Irom Nitrate for the maple grips. That Birch has some crazy figure in it.

 

[KingOfKindling]

I'd try Irom Nitrate for the maple grips. That Birch has some crazy figure in it.

Yeah, Iron Nitrate is definitely in the running for the Maple, it's actually the first thing I try on most woods when experimenting, and the go to for maple.

In fact, here's a test on the Birch. Maybe a bit darker than I'd have liked, but it really brings out the richness of the wood.

Iron Nitrate applied and still wet. Makes me think the wood would look pretty awesome with just oil applied, no stain. At least for a nickel or stainless gun.

Here's the iron nitrate after a bit of going over with the heat gun.

And here it is with a coat of tung oil. Didn't get a picture as my hands were very messy, but the first bit of oil added to the wood made it very dark. I applied the oil with a scotch bright pad and was able to knock back a lot of the black.

Makes for a pretty awesome deep rich color. If I go with this, it should look even better on the grips. I'll do a more thorough job sanding them than this quick test piece.

 

[NeilMacleod]

Awesome !

 

[KingOfKindling]

Got some more samples going.

Top is of course the previously shown Iron nitrate. It's gone dull, but that's generally how the first coat of tung oil goes.

Next is Laurel Mountain Forge Cherry on the left, nothing in the middle, and LMF Maple on the right.

Third down is a light coating of Maple followed by a light coat of Cherry.

Fourth is a heavy coat of Maple, and a heavy coat of Cherry. Dunno that putting the stain on changed things much, guessing the wood kinda stops absorbing stuff.

If I want it to be darker I might just need to do multiple coats of stain, letting in dry in between.


Might see about doing a really light coat of Iron nitrate, heating it, then sanding it back. If I can get it lighter than the previous Iron nitrate, some cherry over the top might look really good. Can apply oil to it after the cherry dries.

 

[JeffG]

Ok, WOW. Excellent work.

 

[springfield art]

So, I've got big hands, and navy sized grips really are just too small. The army grips are a bit better, and I've got a Pietta 1860 franken gun with navy grips I wanted to swap out. The triggerguard and backstrap parts were available, but no decent grips were popping up. Taylor firearms sometimes stocks raw grips, but they were out.

Figured I'd try and make my own. Could do it by hand, but I have 3D printers and a home built CNC router, and in the future I'd like to make a detachable buttstock (since they're pretty much unobtanium). Some grips seem like good practice, and my CNC machine needed maintenance. I can tune the machine, and practice cutting stuff without being out as much as a full stock.

Started out with modeling a grip in Fusion360, then 3D printing various test samples. This one is a bit early, I settled on being a bit more oversized to make sure final shaping would be as good as I can do.

View attachment 351274

First wood cuts were on a piece of curly maple board I had on the shelf. This is a 7mm 4 flute bit. Travel speed of 20 inches per minute and spinning about 20k rpm.

View attachment 351275

After the roughing was completed I did the finishing pass with a 1/16 2 flute ball end mill. Was all I had, and didn't have enough clearance so I needed to get fancy with the CAM settings. Was able to finish the grip, but the grip ended up a bit long. No big deal, I've since had some proper bits arrive. Had video of the finishing pass, but it's too big to upload apparently. Here's a picture instead.

View attachment 351276

Fit is pretty good on my test gun. This one has a factory Army grip, so it makes for a good template. More material to remove by hand than I'd like, but with some minor tweaking and the correct ball end mill the next pieces will be better.

View attachment 351277

I've got some Karelian Birch I'm playing with, and some various maple burl wood coming. Still shopping around for a nice chunk of highly figured walnut.

Neat-O!