Pauly Walnuts
32 Cal
Just went to pop a cap for the first time with my new pedersoli scout. The cap kind of just smushed and it didn’t go off. How do I get my caps to ignite?
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Percussion Caps
- Thread starter Pauly Walnuts
- Start date
Help Support Muzzleloading Forum:
Phil Coffins
69 Cal.
Re-**** and try again, if it pops then the fit of the cap to the nipple is too tight.
If the nipple is too tight for the caps, you can remove nipple, chuck it in a cordless drill & use a fine file on the side of the nipple to make it thinner. Won't take much time to grind the nipple narrower.
It should work fine upon placing it back on the gun.
It should work fine upon placing it back on the gun.
Pauly Walnuts
32 Cal
I tried a different tin of caps and those caps worked. Maybe I have a bad batch?
Are they #11 caps? What brand?
Pauly Walnuts
32 Cal
#11 cci caps. I ordered them from muzzleloader.com. I’m going to go to my local bass pro to see if I can find any more.
I would try a few more from the first tin and see if you have the same results.
Sparkytfl
32 Cal
I've noticed that even with the same brand, some packs just fit a tiny bit tighter and don't easily fit all the way on. But still, even when the nipple is dirty and the caps only go halfway on, I've never had one fail on a gun with a properly strong spring. Related to that, is your spring strong enough? Take the lock off, put a block on a scale, push the hammer down on the block, and (from what I've read) it should take about ten pounds to **** it. I have one that was about six pounds when I bought it, and it would take three hits to pop a cap.
Pauly Walnuts
32 Cal
I’m not entire sure what i did but I took the nipple off and cleaned it, put it back on and it popped caps from both tins no problems now.
I've never had a problem with CCI. Maybe it's your nipple. When I shot percussion, I had better results out of White Hot nipples.
ohio ramrod
75 Cal.
- Joined
- Aug 21, 2008
- Messages
- 7,473
- Reaction score
- 2,209
I have found that you need a sharp edge to the nipple and a fit that is just tight enough to keep the cap from falling off.
- Joined
- Feb 3, 2022
- Messages
- 905
- Reaction score
- 1,343
One thing to note is that caps by different manufacturers are slightly different sizes even if they are the same # cap.
So CCI #10s are a bit tighter fit than Remington #10s.
Then, too, Scheutzen musket caps are made from steel not brass like most others. So they don't hammer down on the nipple as nicely.
So CCI #10s are a bit tighter fit than Remington #10s.
Then, too, Scheutzen musket caps are made from steel not brass like most others. So they don't hammer down on the nipple as nicely.
A new gun should be cleaned up good before you try shooting it.
They usually grease them up at the factory before shipping.
TDM
Cannon
- Joined
- May 28, 2022
- Messages
- 9,659
- Reaction score
- 24,220
- Location
- Louisiana & My camp in Mississippi
As deermanok said, make sure your new Scout has been thoroughly cleaned of the factory grease. You’ll have a batch of cleaning and firing problems if you don’t.
sportster73hp
50 Cal.
- Joined
- Jan 16, 2020
- Messages
- 1,027
- Reaction score
- 801
Too much grease or dried oil on the back side of your lock will slow the hammer and can result in poor or no ignition. Has the same effect on flint guns.
