• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Safely Storing Black Powder

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Bob McBride

54 Cal.
Joined
Apr 23, 2020
Messages
1,815
Reaction score
3,708
Location
Short Mountain, TN
Let's see your black powder storage solution. Perhaps new folks, and there do seem to be a lot lately, will likely be concerned about how to do it safely, and can get some ideas from everyone's method. Here's mine:

IMG_0164.JPG
IMG_0165.JPG
IMG_0166.JPG
 
The best way to store black powder can be found on the back of Goex and Swiss containers.

It is shipped from the manufacturer in a nice heavy card board box.
 
On the back of my Swiss can: (And I paraphrase)

#1) Keep it in the can it came in.
#2) Don't store it floating in a barrel of gasoline.
#3) Store according to the law.
#4) 'Close the lid'.

Handy.

Any thoughts on where to put one's cardboard box full of explosives?
 
Last edited:
As you might expect, there are very strict regulations in the UK about storing black powder. You end up with a box like this. Each section must hold no more than 1kg of powder and there must be 30% space between the top of the bottle of powder and the lid. The walls of the box are 18mm plywood and there has to be intumescent strip around the top. The local police inspect the box before you get a licence to purchase BP.
 

Attachments

  • 5A2125F9-E07D-4240-B56C-E05D9A0FE11A.jpeg
    5A2125F9-E07D-4240-B56C-E05D9A0FE11A.jpeg
    91.6 KB
I store mine in this wooden boot box in original containers or in plastic range boxes after seeing the box inside the box idea I might have to hammer out a few half-inch plywood boxes this weekend
 

Attachments

  • 5F0BEB00-688A-4CBA-BADE-A8CA77757AE5.jpeg
    5F0BEB00-688A-4CBA-BADE-A8CA77757AE5.jpeg
    112.8 KB
  • 70A993C9-5E19-4281-96B2-AD41B7ED522C.jpeg
    70A993C9-5E19-4281-96B2-AD41B7ED522C.jpeg
    113.2 KB
  • 8CFD1BC0-21CA-4048-AC26-7F8F196FEB68.jpeg
    8CFD1BC0-21CA-4048-AC26-7F8F196FEB68.jpeg
    122.7 KB
as Rudall say its very specific here but the health and safety executive did quite a lot of research and trials before deciding, going as far as building a small block built 'room' and sitting the various options on a small cooker to see which one lasted the longest and did the least damage. got to see the videos of the trials at Ordcon that year (Security Check Required). its a bit of a pain but you can see the logic.
 
This thread has gotten me thinking. I had the bright idea of pre-loading charges for my ROA by using small plastic tubes to save the time of measuring in the field. Now I'm wondering if I might be creating a hazard due to the possibility of static electricity, especially here in AZ with our low humidity. Any thoughts? Thanks.
 

Latest posts

Back
Top