Woodsrunner sights

[Siringo]

Just to pass along some information, I changed the sights on my Woodsrunner to a taller set with a 1/10” wide front sight.

From TOW I used a FS-PA-39-B front sight and a RS-FG-16 T rear sight. The front sight is .4 inches high with an oversized dovetail. I reduced the thickness of the dovetail from .125 inches to .050 inches (this is what the Kibler dovetails are cut at. The dovetail width in the sight was larger than 3/8, so when I reduced the thickness I still had enough width the file it to 3/8. Some minor adjustments to the front sight may be needed to adjust POI. Also if you don’t want to go as high, a FS-PA-16 can be used but the front sight would need to be filed down a fair amount. But these would still be taller than the original sights with the kit.

 

[SeaRun1]

Thank you for posting this! Is the “FS-PA-16” number correct? I can’t seem to find it?

SR1

 

[BigAl52]

Thank you for posting this! Is the “FS-PA-16” number correct? I can’t seem to find it?

SR1

Check the number he posted. Yours isnt matching. I just ordered both of these yesterday from Track

 

[hanshi]

I don't like tall sights on a muzzleloader. Despite my aversion to them I have a few rifles with tall sights. Being rather lazy I mostly leave them alone, although I have filed down the sights on at least two of them to look a bit more authentic. Since I can't see worth a hoot the sights are somewhat useless, more or less, for my shooting. I just tell other shooters that I aim by sense of smell.

 

[Nav]

Are tall sights just a personal preference? Do you think it increases your accuracy? Do you think they're easier to see?

I have just the stock sights on my Woods Runner, and I had to pass a needle file over the front and take off a little when sighting in and drifting (though, it was really close just "snapped" together).

 

[Siringo]

Are tall sights just a personal preference? Do you think it increases your accuracy? Do you think they're easier to see?

I have just the stock sights on my Woods Runner, and I had to pass a needle file over the front and take off a little when sighting in and drifting (though, it was really close just "snapped" together).

When I mount the rifle the sights are right there now. I don’t have to crane my head and neck, move my read rearward to align the sights. Personal preference.

 

[Siringo]

Thank you for posting this! Is the “FS-PA-16” number correct? I can’t seem to find it?

SR1

Sorry it is wrong. It’s RS-FG-16. The taller version has a “T” after it.

 

[Siringo]

Just to pass along some information, I changed the sights on my Woodsrunner to a taller set with a 1/10” wide front sight.

From TOW I used a FS-PA-39-B front sight and a RS-FG-16 T rear sight. The front sight is .4 inches high with an oversized dovetail. I reduced the thickness of the dovetail from .125 inches to .050 inches (this is what the Kibler dovetails are cut at. The dovetail width in the sight was larger than 3/8, so when I reduced the thickness I still had enough width the file it to 3/8. Some minor adjustments to the front sight may be needed to adjust POI. Also if you don’t want to go as high, a FS-PA-16 can be used but the front sight would need to be filed down a fair amount. But these would still be taller than the original sights with the kit.

Correction to post. RS - FG-16 not FS-PA-16.

 

[Siringo]

Thank you for posting this! Is the “FS-PA-16” number correct? I can’t seem to find it?

SR1

Should be RS-FG-16. Sorry.

 

[TonyC]

Correction to post. RS - FG-16 not FS-PA-16.

So to be clear, which sight did you use? RS-FG-16 T or RS-FG-16

 

[Siringo]

So to be clear, which sight did you use? RS-FG-16 T or RS-FG-16

I used the RS-FG-16T.

 

[user 34300]

Just to pass along some information, I changed the sights on my Woodsrunner to a taller set with a 1/10” wide front sight.

That is exactly how I make them. Low HC sights have mirage problems. I found that the low HC sights will become impossible to get a decent sight picture while load testing at a leisurely pace. I also like a wider front sight. A wider front gives me smaller groups on paper targets. I always replace the low slung HC sights with front and rear I make myself. My sights are only a little higher and do not look silly. I have never heard a good explanation of why unusable sights were installed on very accurate long rifles, it makes no sense to me. I sure wish there was a target sight option when ordering the kit.

 

[Siringo]

I used the RS-FG-16T.

Used With the tall front sight that stands 0.400 above the barrel. You’ll have enough to file the front sight down.

 

[Bnewberry]

Some people find that when target shooting the heat from the barrel distorts the lower sight picture more than a tall one. The downside is a taller sight can make your cheek weld ”weak” because it is more of a jaw weld due to needing to raise the line of sight up.

 

[Leatherbark]

Sometimes a lot of that mirage might or might not be coming from the inside of the barrel out of the muzzle. I've heard of people using tape over the end to alleviate the heat shimmer from coming out of the muzzle if the firing is fast between the shots. Tape blows off on the next shot. Not sure if any of this is true, just what an old timer told me once...............Bob