• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Nipple wiggling

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Glad y’all had this thread. I picked up a TC Hawkin in .50 perc. A couple of years ago. Nipple only seated hard the last turn. Never knew about the different threads would always retighten between shots. Guess I have been protected 😃 from my own self. Shoots really good with 70 grns and a round ball. Only paid $100.00
It sounds as if you got a good deal on a shooter!

Nipples for percussion muzzleloaders come in a bewildering variety of thread diameters and pitches, and in just looking at one, it may be difficult to tell exactly what it is. A 6mm nipple, for example, is pretty close to a quarter of an inch and the difference may be hard to distinguish (6mm = 0.2362", while one-quarter of an inch equals .250"). However, they are not interchangeable! Not safely, anyway.

It is not unusual for a nipple in a well-maintained gun to turn in easily, and the wrench may only be needed to snug it up, or break it loose if you are removing it. However, if it "only seats hard the last turn," that doesn't sound right to me. A 6mm nipple may easily go in a quarter-inch nipple seat for several turns, until the mis-matched threads begin to bind. From the description, it sounds as if that may be what is happening.

Your T/C Hawken should have been tapped for a 1/4-28 nipple (note that 1/4" is .250"). Please take that nipple that "only seats hard the last turn" to your local Ace Hardware or Lowe's to their specialty screw section and verify the thread size. Better yet, have a machinist check it. If the nipple is not verified to be threaded .250"-28, your best bet will be to discard it and buy a new nipple of the correct size.

However, sometimes the nipple seat on an older gun will have opened up a little, so that even the correct nipple feels a little loose. Track of the Wolf sells slightly oversized nipples in increments of .005" to compensate for this wear. For example, if the female threads in the gun's nipple seat started out as .250-28 but have opened up with wear, you can try a .255-28 nipple... the diameter is slightly larger but the TPI is the same. If it's still too loose, you can try a .260-28. They make these all the way up to .275" diameter with 28 TPI.

In any event, you really need to know what size nipple your rifle is intended to use, and it is essential that the nipple be sized to fit it properly. You really don't want a nipple to blow out, that close to your eye.

Safety first.

Best regards,

Notchy Bob
 
Tc new englander..

I got musket nipples 1/4 × 28... traditions ones..

I noticed they have a little slight wiggle.. so im using the #11 it came with and there solid in there..

The traditions nipples are fine in the dp10 though..

Just trying to find another brand to try...
You have a Traditions rifle?! They use a metric threaded nipple
 
Tc new englander..

I got musket nipples 1/4 × 28... traditions ones..

I noticed they have a little slight wiggle.. so im using the #11 it came with and there solid in there..

The traditions nipples are fine in the dp10 though..

Just trying to find another brand to try...
I suggest you take the original nipple to a machinist or into your local hardware store and determine the diameter (fractional inch or metric) and thread pitch. Then purchase a replacement that has those same dimensions and thread pitch. As stated in your post, (boldface type) the original nipple fits properly.

Hope you solve your problem quickly.
 
Tc new englander..

I got musket nipples 1/4 × 28... traditions ones..

I noticed they have a little slight wiggle.. so im using the #11 it came with and there solid in there..

The traditions nipples are fine in the dp10 though..

Just trying to find another brand to try...
A TC New Englander is sized for a 1/4-28 threaded nipple. An M6 x 1 threaded nipple for a CVA or Traditions gun will definitely fit in a 1/4-28 thread hole, but in the case of a nipple and the pressures it will see, IT IS NOT SAFE and will be ‘loose’. Suggest you take your gun to a competent gunsmith that is familiar with traditional muzzleloaders.
 
It's thompson center new england 1/4 × 28

The nipples I got are traditions brand 1/4 × 28... They thread good that feels okay.

I'm just guessing.. That's the picture of the tradition's nipple and I think it's a different base if that makes sense

I don't want to remove the number eleven factory.
 

Attachments

  • 17155031396876806808935522615712.jpg
    17155031396876806808935522615712.jpg
    1.2 MB
  • 17155034255623639620527952232552.jpg
    17155034255623639620527952232552.jpg
    647.7 KB
Right there is where they look different to me...
 

Attachments

  • Screenshot_20240512_045338_Chrome~2.jpg
    Screenshot_20240512_045338_Chrome~2.jpg
    280.3 KB
  • Screenshot_20240512_045156_Google~2.jpg
    Screenshot_20240512_045156_Google~2.jpg
    211.3 KB
  • Screenshot_20240512_045357_Chrome~2.jpg
    Screenshot_20240512_045357_Chrome~2.jpg
    193.4 KB
Back
Top