Thank, I appreciate it.
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Comer's Gunworks
- Thread starter Michael Comer
- Start date
Help Support Muzzleloading Forum:
Smokey Plainsman asked for some photos of some of my defarb work. Here are some of a Euroarms 2 band Enfield and a Pedersoli Brown Bess that I just finished and sent back home. You can find others in the photo section of my Facebook page. Notice that the Greise markings have been removed from the lock plate and replaced with an engraved Tower.
Attachments
See above.
Last edited:
Dandy work Mike!
1General_Grant
40 Cal
What finish do you use on the stocks?
Michael your a welcome & needed addition to the forum 
Jason60chev
36 Cl.
- Joined
- Jan 9, 2022
- Messages
- 81
- Reaction score
- 154
Michael Defarbed a Remington Pocket revolver for me a good while back, to help prepare it for nickel plating.
I was very pleased. All markings and script were removed from the barrel flats, with no gouges nor low spots and
the edges of the octagon barrel remained crisp and not rounded.
I was very pleased. All markings and script were removed from the barrel flats, with no gouges nor low spots and
the edges of the octagon barrel remained crisp and not rounded.
I do have to ask that since you defarbed the P53 and Bess, why didn’t you square the little wings on the lock screw escutcheons and remove the LA Co markings? And you forgot the lock panels on the Bess.
Last edited:
Hello Clark, It has that particular look because I defarbed it as a London Armoury gun. They were different than the Birmingham guns. If you'll notice I took the lines off the plate and the hammer. London guns did not have these. I took the "London Armoury" stamp off the plate that Euroarms put there. That L.A. Co over the year is an accurate stamp. From what I have read, the round eared escutcheons could be found on London guns as could the square ones and you could also find both types of barrel bands. The Baddeley bands were not standard until sometime in 1862. If a customer wants the square eared screw escutcheons on a London, I'll gladly put them on. So, that's why it looks like it did. It also has the London barrel proofs and is marked L.A.C. on the top of the barrel. I'm not sure what you refer to by forgetting the lock panels on the Bess. I assume you mean the little ears on the end? Once again, my understanding is that the flat panel did not come into the Bess design until after 1775. I figure most guys doing Rev War would have impressions before that but, if I'm in error and they should be gone, then I'd be glad to change that.
I strip off the factory finish. They seem to have a lot of poly or something in them. I then use a dark walnut stain from Laurel Mountain Forge, followed up by hand rubbing a few coats of boiled linseed oil into the stock.
Yes, I know very well about the P53 Enfield. So what did you specifically choose a London gun when somewhere in the neighborhood of 80% of the P.53s brought over were BSAT guns and most London guns were private makes with names on the plates?
And on Besses, the lock panels were always thin and all models.
I only do that on old Euroarms guns because of the bands primarily. Simple answer is cost. Most folks don't want to buy a set of bands to make it a Birmingham. If a customer says put the Baddley bands on and make it a Birmingham, that's what I do. I also do them as a Potts and Hunt if that is what is wanted. If 80% of about 300,000 weapons were Birminghams, that leaves 20% that were not which is about 60,000. Not an insignificant number. And, even though they were certainly in the minority, there were London Armory guns over here. So, there you go. That's why I do what I do. I provide a service and that is directed by what my customer tells me they want. I try to provide the best product that I can according to my ability and knowledge. but I'm more than open to constructive criticism and am willing to change how I do things to make a better product, which I have indeed done over the years.
I'll do some more research on the Bess and adjust my work to what photos show me.
Those Baddely bands can be corrected. We were doing that back in the early 90s.
Eric Goldstein has a good book on the Brown Bess with lots of detailed photos both assembled and disassembled.
Yes, they can. I've played around with them a bit. I'll check into that book. I'm sure it would be a help.
Funky site, tried to order and got a empty cart after adding item. Is this a scam site?
Nope. What specifically happened? There have been problems if you go there from a Google link. Best to type the address directly. Let me know if you continue to have trouble and I'll let the host know.
Thanks Mike, I had connected via Google and now have a direct link. I was able to complete my order, create an account with the direct link. Thanks again. Google is my browser.
Sounds good. Thanks for your business.
Seems like I spoke too soon. Once I use the "reset password" option I am ALWAYS signed in and there is no option to sign out or update my account nor see what I have purchased and its status is. When I do a direct link to the site I am automatically logged in. Not what I would call a secure feature. And my attempts to login via the site are rejected - invalid password. Definitely a programming issue with the login process.
I'll send this to somebody to look into.
