• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Info please with cocking effort on Hawken percussion lock

the hawken shop
Shop deals on ebay
shop deals on amazon
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Larry (Omaha)

Larry (Omaha)

69 Cal.
MLF Supporter
Joined
Aug 27, 2004
Messages
3,225
Reaction score
7,143
I have a nice Hawken style percussion lock that works well, except it is punching the cap lids into the nipple flash hole. What is going on? Well, when I started looking at it, I realized the cocking effort is waaaaay too stout. I will trim the mainspring to lower the cocking effort. My question to the forum: What is a good poundage to shoot for? I can't give you a lock brand as I do not know. It is a leaf spring, not a coil spring.
Thanks in advance
Larry
 
Are. M. said:
When you say trim the spring, where is the metal coming off of? The hook end, the side of the spring, or the flat of the spring?
Click to expand...
I am no expert, but in my years of working with locks I have done both. Thinned the thickness and also removed material from the width. Depending on what I have and the intended end result, I may do both the aforementioned or just one. Two issues I consider are: never leave cuts, scratches, or grooves at right angles of the spring length. If grinding never get the spring too hot to hold. Again, not an expert, this is what I do.
Larry
PS I work on the hook end of the spring, but don't touch the hook
 
Davey Boy said:
Before you wreck the spring, why not look at the flat inside the hammer and look at the nipple surface to see if it is also flat and the two surfaces are in complete contact?
Click to expand...
Not bragging, but I made the rifle. The lock, barrel and drum were all tuned/timed when it was made. The punched out wafer of cap lid is a solid round that fills the nipple flash hole. The spring tension strenght is way too stout. Even if the lock wasn't punching holes in cap lids, the spring needs to be trimmed.
Thanks for a good point
Larry
 
Larry (Omaha) said:
Not bragging, but I made the rifle. The lock, barrel and drum were all tuned/timed when it was made. The punched out wafer of cap lid is a solid round that fills the nipple flash hole. The spring tension strenght is way too stout. Even if the lock wasn't punching holes in cap lids, the spring needs to be trimmed.
Thanks for a good point
Larry
Click to expand...
You just might need a shorter nipple ----:dunno:;)
 
first off i would recommend acquiring a replacement spring before working on the current one. nothing ruins my day like having a two piece main spring and nothing to replace it with for a month or so while some shipping entity attempts to lose or destroy it .
as to the work you are contemplating, i think you are on the right path, and i think you have the ability. go for it!
but, when you have the spring off work the hammer to see if there is galling or some fumunda causing the extra effort. check the bridle for wear around the axel. that can cause a bind.
 
Maybe I didn’t understand the question but I measured the amount of pull it takes to cock a couple rifles. Both started at about 11 pounds to half cock then one increased to 15 pounds. The other (a Siler kit) went down to 7 pounds to full cock. Both percussion of coarse.
 
deerstalkert said:
first off i would recommend acquiring a replacement spring before working on the current one. nothing ruins my day like having a two piece main spring and nothing to replace it with for a month or so while some shipping entity attempts to lose or destroy it .
as to the work you are contemplating, i think you are on the right path, and i think you have the ability. go for it!
but, when you have the spring off work the hammer to see if there is galling or some fumunda causing the extra effort. check the bridle for wear around the axel. that can cause a bind.
Click to expand...
Thanks, all good points to ponder. If the bridle has wear or is binding, why is there so much downward energy to punch holes in the Remmingon #11 caps on a Hot Shot nipple?
I shoot flint 95% of the time. If this spring gets ruined no big deal for a shipping wait, cuz it would most likely be hanging on the wall anyway.
Larry
 
Phil Coffins said:
Maybe I didn’t understand the question but I measured the amount of pull it takes to cock a couple rifles. Both started at about 11 pounds to half cock then one increased to 15 pounds. The other (a Siler kit) went down to 7 pounds to full cock. Both percussion of coarse.
Click to expand...
You did and thanks.
Larry
 
like you Larry I shoot flintlock 99% of the time and only build flintlocks. but having gone through several dozen TC's cap guns and a like amount of Investarms of many flavors, I have some knowledge of them, unless i have forgotten that info. doing alot of that these days.
I would suggest trying some other caps to see if it is something inherent to the Rem caps.
if the bridle/axel is worn oblong the forces may be greater going back or ahead.
let us know please how you cure this. good hands on knowledge is worth having. if I could remember it!
 
deerstalkert said:
like you Larry I shoot flintlock 99% of the time and only build flintlocks. but having gone through several dozen TC's cap guns and a like amount of Investarms of many flavors, I have some knowledge of them, unless i have forgotten that info. doing alot of that these days.
I would suggest trying some other caps to see if it is something inherent to the Rem caps.
if the bridle/axel is worn oblong the forces may be greater going back or ahead.
let us know please how you cure this. good hands on knowledge is worth having. if I could remember it!
Click to expand...
Right you are on the caps. The gun was made in the 80s. Can't be more than 300 to 400 rounds through it, so worn parts are non issue. When I shot it in the 80s, I used CCI caps.
Larry
 
Larry (Omaha) said:
Ok, how does that help the horendous effort to draw the hammer back? Seriously I don't understand how that would reduce the spring tension.
thanks
Larry
Click to expand...
It doesn't do anything about the spring force but it might help with punching out the center of the percussion cap and clogging up the nipple hole.
 
Rebel bull said:
I would say that it is a function of the lock/inlet check the lock out of the gun
Click to expand...
Not trying to be a smart as_ but come on, really, how can a lock have too much downward hammer energy because of lock wood interference?
Larry
I am running over 12 pounds of hammer cocking effort, and punching holes out of the cap lid at hammer fall. Poundage is measured at the hammer thumb grip.
 
The rifle that I measured for you that has 15 pounds to full cock doesn’t punch holes in the caps, perhaps your nipple has a narrow edge where the cap seats. My preferred cap is Remington #11 but often CCIs are used with no difference.
 
Never thought much about hammer pull weight, only trigger pull. Just now I got out my TC Hawken percussion kit gun with only about 25 shots through it and measured the hammer cocking strength, it came out to 11 pounds 13 oz. Next, I tested my most recent build which is a flintlock with a Deluxe Chambers Siler lock, the cocking weight was 10 pounds, 8 oz.

I never have had a percussion lock hammer cut a cap at the above cocking poundage, which appears to be a standard ball park figure for all of my locks.

I have one of these fancy trigger pull digital scales to check things with.

trigger pull scale.JPG
 
Sorry, I did not read right. I see the cap metal is being punched, what I get is the covering over the priming compound.. I would change the nipple.
 

Similar threads

T
Doglock lock problems...
Replies
9
Views
338
rich pierce
R
Frontstuffer070
  • Locked
SOLD Unique One Of A Kind (Mule's Ear, Side Hammer, Striker?) .50 Cal READ entire description please.
2
Replies
22
Views
1K
buzzard
B
Clukmyrooster
Uberti 1862 Pocket Police
Replies
9
Views
826
Clukmyrooster
Clukmyrooster
Sparkitoff
Older TC percussion lock no half-cock
Replies
2
Views
449
necchi
necchi
W
Spring compressor (cramp in English gunsmith terms) for Lyman Deerstalker.
Replies
3
Views
439
webfeet
W

Latest posts

Back
Top