Best revolver nipple wrench

the hawken shop
L & R
shop deals on amazon
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Rebel

Rebel

Cannon
MLF Supporter
Joined
Mar 21, 2004
Messages
8,251
Reaction score
382
Location
Oregon
I have an old 1971 made Uberti 1858 Remington with 5 Very stuck nipples. I tried soaking in Kroll. No luck. Then i soaked in Liquid Wrench penetrating oil and i even put an old nipple wrench on and smacked it with a hammer some. Still no luck. So, which is the strongest most durable nipple wrench? The Ted Cash ratcheting or the Slix Shot T. Or some other? I already rounded the edges on a Traditions T and a Track Of The Wolf T.
 
The wrenches Slix Springs sells are pretty robust. The Traditions wrenches most certainly are not. I think I also remember seeing a post here somewhere and somewhen where somebody had modified a hex socket wrench driver to fit a revolver nipple. If you have or can make a wrench with a nice tight fit then you can put the cylinder in a vise (pad protected, of course) and get some decent torque using a pipe wrench over the nipple wrench's cross bar.
 
Thanks. I put 2 dowels in my vise to fit in 2 of the chambers and then put the cylinder over them so i could get more leverage.
Still nothing. I have heard good things about both the Slix Shot and Cash but have never used either.
 
After bending a couple of nipple wrenches I filed a notch in a 3/16 by 1/4 drive socket. It looks thin and flimsy but it took the nipples right out of my 1851 Pietta. 1/4 drive sockets are cheap so if you screw one up it's not a worry. Some guys use Dremels to cut the notch but I just filed it with a flat file on edge. Try it.
 
Tedd Cash is the best that there is..

You might try putting the cylinder is a sonic vibrator and Liquid Wrench.

The very best penetrating stuff is BP Blaster. Hose down the cylinder with it and put it in a Baggy for a week. Nipples will come out.
 
Last edited:
Has anyone used an impact driver ?
 

Attachments

  • 2Q==(1).jpg
    2Q==(1).jpg
    4.2 KB
Actually, the best penetrating oil is Power Steering Fluid (PSF) and acetone 50/50 mix.

Heat with a small torch, tap on it, torque it clockwise, then counter clockwise, tap on the socket while torqueing, then go through all those steps again, and again, and again.......

Be patient. Yeah, I know, after a little while it feels like it's never coming, like it's welded in - but then, suddenly, there will be a snap and the wrench will move slightly. There will be the slightest movement. Go back and forth - tighten, loosen - but don't force it or it'll get stuck all over again. What you want is for the movement to draw penetrant deeper each time. Very quickly you'll get more movement until finally it'll thread out.
 

Similar threads

B
1864 production Remington 1858 New Army- how to remove nipples?
Replies
13
Views
978
Relic shooter
Relic shooter
11Bravo
JB weld to the rescue
Replies
5
Views
801
11Bravo
11Bravo
Ed C.
My experience with Walker cylinder gap and some other notes.
2 3
Replies
58
Views
6K
M. De Land
M
hawkeye2
Ted Cash Ratcheting Nipple Wrench
Replies
0
Views
1K
hawkeye2
hawkeye2
Alaskagrizz49
  • Locked
SOLD Like New Stainless .44 Ruger Old Army with Adjustable Rear Sight
Replies
7
Views
2K
Alaskagrizz49
Alaskagrizz49

Latest posts

Back
Top