.32 Kentucky
Last edited:
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
A little Pedersoli before and after. Faux Curly Maple
- Thread starter pacanis
- Start date
Help Support Muzzleloading Forum:
Thanks.
We were talking about it in another thread.
Wrap with wire, light torch and hope for the best.
- Joined
- Jun 17, 2019
- Messages
- 8,314
- Reaction score
- 9,680
Does 'liven' it up a tad!
I love it. What a difference!!
Thanks guys.
TDM
Cannon
- Joined
- May 28, 2022
- Messages
- 9,651
- Reaction score
- 24,190
- Location
- Louisiana & My camp in Mississippi
I like it. Good job!
Point us in the right direction PLEASE. Sounds REAL interesting.
- Joined
- Sep 24, 2008
- Messages
- 605
- Reaction score
- 841
Very nice!! Looks beautiful.
Fantastic. What an improvement. Very impressive.
Here's the "go to" video. The one I found the most complete and someone else posted the same one.
But there's a lot of learning on the fly. For me anyway.
Things I found:
Practicing helps, but unless you are burning the exact wood it is not going to burn the same. Not even another stock (Am walnut compared to whatever walnut Pedersoli uses in my case).
So keep your eyes on the color changing (charring).
And if you need to touch up spots you might have missed, watch overheating the wire that is already pretty hot. If they get cherry, which happened a couple times with me, you will see the individual wire wraps. And they look nothing like curly maple
I tried this first on a test piece of wood with annealed black wire and the galvanized deflects the flame better.
24ga works well and conforms easily to the curves. And it did not leave grooves like the 20ga wire I tried on my test piece. True Value hardware in my case. Ace did not have any.
I used a typical Bernzomatic turned down pretty low.
My wire wrap job. Don't be afraid to snip it and do sections at a time. No such spools here like the video guy uses.
But there's a lot of learning on the fly. For me anyway.
Things I found:
Practicing helps, but unless you are burning the exact wood it is not going to burn the same. Not even another stock (Am walnut compared to whatever walnut Pedersoli uses in my case).
So keep your eyes on the color changing (charring).
And if you need to touch up spots you might have missed, watch overheating the wire that is already pretty hot. If they get cherry, which happened a couple times with me, you will see the individual wire wraps. And they look nothing like curly maple
I tried this first on a test piece of wood with annealed black wire and the galvanized deflects the flame better.
24ga works well and conforms easily to the curves. And it did not leave grooves like the 20ga wire I tried on my test piece. True Value hardware in my case. Ace did not have any.
I used a typical Bernzomatic turned down pretty low.
My wire wrap job. Don't be afraid to snip it and do sections at a time. No such spools here like the video guy uses.
You SIR did a BEAUTIFUL job!! VERY IMPRESSIVE. 
I remember back a ways, folks were doing the "tiger stripes" on M1A stocks with a torch.
First thing that came to mind looking at YOUR job.
VERY IMPRESSIVE. I remember back a ways, folks were doing the "tiger stripes" on M1A stocks with a torch.
First thing that came to mind looking at YOUR job.
- Joined
- Sep 20, 2010
- Messages
- 1,203
- Reaction score
- 1,226
Now that is tricky… Best grain enhancement Ive seen Fred
Ballshooter
50 Cal.
That turned out awesome was it my posts that, got you thinking hahahha.
Thread 'Did the unthinkable to my GPR but I love it!' Did the unthinkable to my GPR but I love it!
Thread 'Did the unthinkable to my GPR but I love it!' Did the unthinkable to my GPR but I love it!
Attachments
Last edited:
Yeah, I had never run across this process before. I'm glad that thread popped up.
Wow, very cool. You have to do an instructional video.
What a transformation! Looks fantastic
Nicely done.
Similar threads
- Locked
