Another Walker adjustment

[M. De Land]

Still learning the nuances of the new Uberti Walker I acquired last year I recently noticed that the trigger nose is contacting the half **** notch as the hammer falls with the addition of the action shield apparently. My guess of the cause is perhaps the added weight on the hammer or possibly interference fit of the shield in the hammer mortise or to heavy of a trigger return spring.
I'll post back with a cause and remedy when I get it all sorted out.

 

[M. De Land]

Still learning the nuances of the new Uberti Walker I acquired last year I recently noticed that the trigger nose is contacting the half **** notch as the hammer falls with the addition of the action shield apparently. My guess of the cause is perhaps the added weight on the hammer or possibly interference fit of the shield in the hammer mortise or to heavy of a trigger return spring.
I'll post back with a cause and remedy when I get it all sorted out.

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.
I really like the loading lever latch as it works very smoothly and locks the lever very securely in place with the most leverage possible, at it's tip.

 

[M. De Land]

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.

 

[M. De Land]

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.
I really like the loading lever latch as it works very smoothly and locks the lever very securely in place with the most leverage possible, at it's tip.

I may at some point just remove the Walker spring entirely and re-engineer/alter to a Dragoon type flat spring arrangement as the Walker spring has always felt mushy in the middle of the stroke to me. A single leaf flat spring will have a faster response time than does the original Walker design with the two legs and turn back V and very likely make a marked improvement in hammer speed.
I'll take photos and post them if I decide to make the alteration.

 

[bpd303]

I've never seen that type of loading lever latch, did it come from Uberti like that. Interesting to say the least.

 

[M. De Land]

I've never seen that type of loading lever latch, did it come from Uberti like that. Interesting to say the least.

I was praying for a good front latch idea and this is what God gave me ! True Story! I'm a home machinist with a lathe and mill.

 

[45D]

I may at some point just remove the Walker spring entirely and re-engineer/alter to a Dragoon type flat spring arrangement as the Walker spring has always felt mushy in the middle of the stroke to me. A single leaf flat spring will have a faster response time than does the original Walker design with the two legs and turn back V and very likely make a marked improvement in hammer speed.
I'll take photos and post them if I decide to make the alteration.

Have you reduced the cam height and blended the bottom of the cam to that of the hammer surface? That will make a smoother transition for the bolt arm (which should have a polished arc for the transition as well) and impart less drag on the hammer.
Of course polishing the contact surfaces between the main spring and radius in the hammer will make an improvement. This contact patch moves from the rear of the radius towards the middle as the hammer is cycled back. Therefore the contact patch moves to the rear of the radius cut as the hammer moves forward, which actually speeds up the hammer with a camming effect. Watching this happen is exactly where I got the idea of bending the very end of flat mains upwards to speed up the hammer right at the end of its travel.
Just some food for thought . . .

Mike

PS You could also remove some weight . . .

 

[M. De Land]

Have you reduced the cam height and blended the bottom of the cam to that of the hammer surface? That will make a smoother transition for the bolt arm (which should have a polished arc for the transition as well) and impart less drag on the hammer.
Of course polishing the contact surfaces between the main spring and radius in the hammer will make an improvement. This contact patch moves from the rear of the radius towards the middle as the hammer is cycled back. Therefore the contact patch moves to the rear of the radius cut as the hammer moves forward, which actually speeds up the hammer with a camming effect. Watching this happen is exactly where I got the idea of bending the very end of flat mains upwards to speed up the hammer right at the end of its travel.
Just some food for thought . . .

Mike

PS You could also remove some weight . . .
View attachment 363227

Good ideas, thanks, I love to hear about these tweeks ! The added resistance and weight of the action shield and securing rivet I used made a noticeable change in the hammer speed that I noted from before and after. I could have compensated with some holes but didn't want to create more fouling traps. I'm increasingly thinking about altering to a single leaf main spring like in the later models which will speed hammer fall as well.
These Walkers are fascinating critters !

 

[M. De Land]

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.
I really like the loading lever latch as it works very smoothly and locks the lever very securely in place with the most leverage possible, at it's tip.

Into the guts of the Walker again and found that the main spring is making contact with the grip at the bend back. A bit of chisel work took care of that.
Doing some more trigger nose, full **** notch fitting, to get the trigger I like.
Some pictures of the trigger spring reduction.