chisels....lesson learned.

[rocullen]

The last couple of weeks I've been diddling(?) with chisels and everything(a lot anyway) that goes with them.
First lesson I bought a set. Who wants to buy 1 chisel, right?
Second lesson I didn't buy premium chisels, Pfiel, Two Cherries, Pie, Auriou, or any of the well respected.

I purchased a small set off of...well, the net. Starts with a S ends with f.
They were the sharpen them yourself variety and I could get them, um, er, uh kinda sharp, except one and to their credit they sent me a new one of same pattern, 3F-20 and it sharpened up to the same level; almost sharp.

Kinda disappointed, I ordered a Pfeil to compare with; a 7-12.

Meanwhile, I noticed the S****f's were not very uniform on the profile grind, the top defining edges.
I made some hardwood blocks to the profiles of the worst offenders and used them with 220 grit W/D sand paper, then 600.
Helped quite a bit once the edges were cleaned up, but still not SHARP.

The Pfeil came in.......oh, that's what sharp looks and feels like.
The S****fs would hardly cut softwood, much less hard rock maple.
The Pfeil would slice thru(end grain also) it with just a little effort.

Comparing the Pfeils bevel to the others, I reduced the angle of my old 3F-20(leaving the new arrival alone) to match the angle of the Pfeil's; I had to reduce the angle about 7 or 8°, maybe a tad more. Fortunately, I stumbled upon a Makita 982-02 sharpener that needed some repairs to it, got it fixed up and was about to grind without too much trouble/worries.

That brought the edge of the 3F-20 S****f to FEEL like the Pfeil; but it sure didn't cut like the Pfeil.
Since I determined that these chisels from the set were rather useless for intended use(hard maple) I went a head and ground the 6-13 down to the angle of Pfeil and it helped sharpen it up to again FEEL like the Pfeil, but again it sure didn't cut like it.
In both cases I had to exert 1 and a half(or more) times the effort with the "set" chisels than the Pfeil.

I got the set(after grinding/re-beveling)to slice thru pine(maybe whitewood) like butter. The Pfeil would cut thru it like hot butter.
I also bought a Lamp brand from woodcarvers supply and it cut comparable to the Pfeil and about $18 cheaper, but they are a "house brand" and supply is limited.
But we ain't carving pine, so from now on, it's gonna be well known/respected chisels.

 

[Phil Coffins]

Glad you can tell the difference, cheap can be the most expensive thing to buy.

 

[deerstalkert]

i had the worst time convincing the ***** working on a 300.00 piece of wood (me) that a 50-60 dollar chisel was a good investment.
until the cheap chisel the *****(me) was using hogged out a big chip on the lock inlet.
then the ***** listened.

 

[rocullen]

i had the worst time convincing the ***** working on a 300.00 piece of wood (me) that a 50-60 dollar chisel was a good investment.
until the cheap chisel the *****(me) was using hogged out a big chip on the lock inlet.
then the ***** listened.

yep, the sharp one are a lot easier to control.

 

[Gtrubicon]

What brand should a guy be looking for as far as chisels?

 

[rocullen]

I've only had experience with the Pfeil and the Lamp. Both come razor sharp and seem to go forever. It's just that the Lamp brand is Woodcarvers Supply house brand and right now they have very low selection.
I'm gonna try one of the Hirsch from Lee Valley....unless someone tells me it's a waste of money(hint, hint)
I've heard they're good...?

These guys have way more experience/knowledge than I; maybe they'll lend a hand, but Pfeil is available and pretty darn good. There may be better, but they'll cut you from across the room.

 

[TraderVic]

As the old saying goes ; "when you buy quality you only cry once".

 

[Gtrubicon]

I’ve always had Marples brand in my bags, (Construction), I sharpen them myself but don’t think I would put them to work on a rifle stock.

 

[TraderVic]

What brand should a guy be looking for as far as chisels?

As I'm considering a Kibler rifle build, I'm certainly interested in recommended brands of chisels for this work.

 

[necchi]

First lesson I bought a set. Who wants to buy 1 chisel, right?,,,
Second lesson I didn't buy premium chisels,

I had to learn those 2 very same lessons myself.
It's a hard lesson to learn when yer livin a tight budget,, only to find out later that the "bargain" blade set was a loss.
Later on I layed my hands on just one of those Pfeil palm handled tools another feller had,, and learned that there is right in the world.

 

[rocullen]

If you need some straight, carpenter type chisels, the DeWalts from Home Depot are super sharp and seem to hold up well. They're made in Sheffield, if that means anything today.
I also bought a Narex 1/8" pairing chisel and it came very sharp and seems to hold up well.

 

[rocullen]

I had to learn those 2 very same lessons myself.
It's a hard lesson to learn when yer livin a tight budget,, only to find out later that the "bargain" blade set was a loss.

Not a COMPLETE loss. Might want to carve some pine or basswood some day.
I have had a lot more expensive lessons, but that was before I was on a fixed income.

edit: I can use one of those cheap 3F-20 with a mallet and hog off some wood!

 

[billraby]

Pfeil is the way to go. Get one or two every pay day and eventually you will have a nice set of them. The cheap chisels work great for stirring paint.

 

[bud in pa]

About 40 years or so ago I received a set of Craftsman chisels as a gift. If you know how to sharpen them you can shave with them.

 

[sdilts]

Pfeil is the way to go. They have every configuration that you would ever need. I get mine from Woodcraft.

 

[Whughett]

Regardless of brand name, all chisels will need sharpening sooner or later and a man who knows how can get any “decent” tool steel chisel as sharp as any other. It may not hold that edge as long is the difference. Dollar store chisels of mild steel exempted.

 

[John May]

I agree that Pfeil chisels are second to none but I've bought a few 'vintage' chisels from local Antique Centres here in the UK. Generally speaking they need some TLC to get them back from being used to open tins and stir paint but once properly sharpened they hold a far better edge than anything new in my price range.

 

[RobertE]

I’ve been on a Pfeil kick lately, too. Pick up a new one or two a month, when what I need is in stock. I’m also very fond of old Marples chisels. Harder to find, but good ones show up on the auction sites.
Bob

 

[mushka]

Buy the best you can afford, use them, strop them frequently. They'll stay sharp for a very long time. I only carve small figures, chains, spoons, balls in boxes, and other various small things but the knives and chisels need to be good and sharp. Get the best and you will only buy once.
Carving is a relaxing activity.

 

[1BadDart]

I’ve been on a Pfeil kick lately, too. Pick up a new one or two a month, when what I need is in stock. I’m also very fond of old Marples chisels. Harder to find, but good ones show up on the auction sites.
Bob

How can you identify the older ones?