CVA Kentucky Rifle - No Barrel Pin

[Dennis42]

My first post. If I am in the wrong subforum I apologize.

Question:
I have a CVA Kentucky Rifle from the 70's. Long story on the origins of this gun but it is not functional in its current state and I decided I would rehabilitate it. The gun has a JUKAR .45cal barrel. The barrel has very few markings, which I think is cool. Now days they come with an entire safety manual engraved on the barrel.

The stock on this rifle is two parts and the butt stock and fore stock are joined in the middle with 2 metal pins. This is basically the same rifle as the Traditions Kentucky Rifle. In fact, I think it is exactly the same.

With respect to the barrel, I noticed that it has no pins or wedge keys to attach the barrel to the fore stock. The barrel attaches to the tang and there is a nose piece on the end and that's it.

What's more, there are no holes in the barrel lugs anyway, so I guess it was never designed to have pins.

Does anyone have experience with an old CVA Kentucky Rifle and perhaps understand why they were made this way? And is there an easy fix to give the whole thing more solid support?

I don’t think that retrofitting pins is a possibility. There is no way I could line all that up for one thing, and the lugs are quite short so there is no room to drill in a decent size hole. Honestly, I am not even sure why there are lugs on the barrel anyway. They are super short and serve no purpose that I can tell.

Thanks,
Dennis

 

[Loyalist Dave]

Hello Dennis42. Welcome

I'm betting you're not the original owner, OR you bought it and stored it and finally got a good look at it?

The reason is, A) I have the same rifle, from the 1970's. and B) it sounds like it was once a "kit". It sounds that way because you are supposed to have pins through the barrel lugs. Whomever built it first, OR the guy at the factory, didn't bother to complete the rifle. IF it was a "wall hanger" the kit buyer didn't need to finish the rifle. IF it was a guy at the factory, well Quality Control messed up.

The holes through the stock and the barrel tenons need to be drilled and pins need to be used.

LD

 

[ronaldrothb49]

Yes it was intended to have holes drilled through the lugs. A 1/16" pin is all you need the wood doesn't support the barrel. Actually it is just the opposite, the barrel supports the wood. You need to be careful in locating the bottom of the barrel to drill the holes for the pins. A drill press comes in handy for that but it can be done with a hand drill.

 

[Dennis42]

Hello Dennis42. Welcome

I'm betting you're not the original owner, OR you bought it and stored it and finally got a good look at it?

The reason is, A) I have the same rifle, from the 1970's. and B) it sounds like it was once a "kit". It sounds that way because you are supposed to have pins through the barrel lugs. Whomever built it first, OR the guy at the factory, didn't bother to complete the rifle. IF it was a "wall hanger" the kit buyer didn't need to finish the rifle. IF it was a guy at the factory, well Quality Control messed up.

The holes through the stock and the barrel tenons need to be drilled and pins need to be used.

View attachment 368946

LD

It was a kit and it was mine as a kid. In my defense it was about 50 years ago. My dad gave it to me but my dad wasn't the father/son project type so once I got the kit, I was on my own. My dad also didn't do anything that required tools so we had none. Needless to say, it didn't get done and what was cone was done poorly. Despite the way my dad was, I am very much a hobbyist and I dabble in blackpowder shooting a little bit as well. So when I came accross the parts and pieces of this thing, while cleaning out my mothers house, I decided to try and finish it and get it right.

So, I guess I will try and drill this out. Any suggestions on the best way to line it all up such that I get the holes in the right place on the fore stock? I did not find the original pins but I know these to be available online.

 

[Dennis42]

Yes it was intended to have holes drilled through the lugs. A 1/16" pin is all you need the wood doesn't support the barrel. Actually it is just the opposite, the barrel supports the wood. You need to be careful in locating the bottom of the barrel to drill the holes for the pins. A drill press comes in handy for that but it can be done with a hand drill.

I do have a drill press. I don't think I will have any problem getting the holes drilled in the lugs. I just don't know how I will determine where to drill holes in the stock such that it all lines up.

 

[Loyalist Dave]

My dad gave it to me but my dad wasn't the father/son project type so once I got the kit, I was on my own. My dad also didn't do anything that required tools so we had none. Needless to say, it didn't get done and what was cone was done poorly.

So, I guess I will try and drill this out. Any suggestions on the best way to line it all up such that I get the holes in the right place on the fore stock? I did not find the original pins but I know these to be available online.

AH no worries mate. You did what ya could. Time to actually get her shooting though, eh?


LD

 

[2 shots]

you would drill stock with barrel installed. there are plenty of posts on this if you search the forum. there are also tools made for this that make it easier for some. i use a piece of aluminum angle on my press table, put a piece of blue tape on face of angle and the barrel in the area of the lug, hold the barrel[ top flat] against the angle and line up the lug under the drill bit, now clamp the angle to the drill press table make sure the bit is still lined up, now mark a pencil mark on each piece of tape so they line up well, put the barrel back in the stock, line up the marks, make sure top flat is flat and tight on the face of the angle and drill. p.s. first make sure you table is square [90 degrees] with the bit on you drill press.