Dropped Dragoon?

[ajbennettnc]

Got this Colt's Dragoon repro in an auction. Muzzle is slanted; I believe it must have fallen, maybe from a horse. I want to shoot it. Anybody got any ideas about whether this muzzle damage makes it dangerous to shoot? I figure it would need recrowning to make it accurate, but safety is the first concern. Thinking I could just saw it back a bit. The barrel isn't crooked, from what I can tell. Anybody have experience with muzzle damage list this on a percussion revolver? Thanks in advance for advice.

 

[2 shots]

seems that was more than a fall , unless the barrel is made of lead if its only the outside just file it [ outside edge not front] flush again.you will have to measure the inside ,cant really see it in your picture. can you post a pic of barrel from the front?does the bore look round??

 

[earlwb]

I agree. Did someone hammer on the barrel? It looks like it has a lip on the outside edge but what about the inside bore edge too? It may have a lip on it too. I think you need to find a gunsmith to redo the barrel muzzle on that gun.

 

[Jappo]

Can you remove the barrel ? Looks like it was pounded in.

 

[ajbennettnc]

Thanks for input! Good points all, and i appreciate it.
I'll mess it more over the next few days and get y'all some better pictures. The muzzle bore itself looks ok and round, but I will measure it with calipers to check. Jappo, I'll try to remove the barrel and see if I can.

 

[morehops52]

I could be wrong and I hope I am but to me the barrel looks like it could be bulged a little. Did you mic the barrel at all?

 

[Whitworth]

My guess is someone who shouldn't own a hammer did it while pounding out a stuck ball. YMMV

 

[D Yager]

Here's some other things to check, how does the wedge fit, tight or loose and floppy? Judging by the muzzle damage someone was either trying to get barrel off of it wasn't going back together and a don't force it get a bigger hammer frame of mind came into play. This pistol is most likely a Uberti but if it isn't it will most likely ...98% positive.. the arbor is short and possibly loose or out of square with the frame. A tip on getting the barrel off, grab the barrel in one hand and whack the cylinder with a PLASTIC mallet a few times. It should start to move. Did I mention the wedge needs to be out? PM me if you have any questions about having work done on this pistol.

 

[2 shots]

some folks just should not own guns or tools.

 

[Jappo]

some folks just should not own guns or tools.

That's a shame that was done to a Dragoon..

 

[Jappo]

Here's some other things to check, how does the wedge fit, tight or loose and floppy? Judging by the muzzle damage someone was either trying to get barrel off of it wasn't going back together and a don't force it get a bigger hammer frame of mind came into play. This pistol is most likely a Uberti but if it isn't it will most likely ...98% positive.. the arbor is short and possibly loose or out of square with the frame. A tip on getting the barrel off, grab the barrel in one hand and whack the cylinder with a PLASTIC mallet a few times. It should start to move. Did I mention the wedge needs to be out? PM me if you have any questions about having work done on this pistol.

Yep, I think there were only two makers. Uberti or ASM. I could be wrong buts thats all I've seen. I have an ASM 1st model and the 2nd - 3rd are Uberti as is my Whitneyville.

 

[hawkeye2]

Not the way to adjust the barrel/cylinder gap.
If the bore is OK shoot it and go from there. It might only take a little file work. Since it's a repro you could shorten the barrel slightly if needed and no one would notice.

 

[Jappo]

I would at least crown it. The outside is just cosmetic. Nothing a finishing file can't fix.

 

[deerstalkert]

My guess is someone who shouldn't own a hammer did it while pounding out a stuck ball. YMMV

my first thought was there are people who shouldn't get nourishment.
without better pictures and a new pair of eyes to see them, It looks like maybe it could be fixed by a 1/4 inch amputation and re-crown.

 

[Malamute]

You can true it up relatively simply. Ive used the Lee case trimmer guides, find one close enough to your bore that it can be turned down (can probably get by with a drill press and file/sandpaper) to just slip into the bore, attach the cutter. Use black sharpie to dye the muzzle, insert guide and cutter. Only gently turn the cutter to indicate where its high, carefully file, recheck until square. The crown on many was very nearly non-existent, but you can crown it by several methods. If the bore is affected, it will have to be cleaned up first to allow the bore diameter pilot to slip in. The outside can be cleaned up to look good.

Ive cut rifle barrels down with this method, it works reasonably well.

 

[SDSmlf]

I would start by checking the bore with precision gauge pins.