- Joined
- Jan 31, 2009
- Messages
- 13,037
- Reaction score
- 7,296
I'd go with a smaller bore sleeve, probably octagonal to round exterior contour.
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Hole Through the Barrel
- Thread starter Splitear
- Start date
Help Support Muzzleloading Forum:
Pete G
76 Cal.
I don’t see any difference between that and the “clean out” screw, safety wise. It may cause some issues with patches, however.
Sandro_Ventania
40 Cal
If a hole in the barrel was a problem, we couldn't have flintlock. After all, what is a touch hole? But if your conscience doesn't let you calm down, make a short rifle or two pistols. Both will be fun.
- Joined
- Dec 15, 2016
- Messages
- 1,566
- Reaction score
- 3,964
The exact reason I will not buy a barrel with extra "sight holes" in it, be it for primitive sights or a scope. Too often the holes are drilled all the way through to the bore.
Ultimately is less that I'm worried about shooting it (even less so from some of the comments), but I really don't need it, and don't want to sell it with something that even has a small potential of being unsafe.
A friend of mine has offered to take if off my hands for a "project". I'm not sure what he has in mind, but I'm sure it will be interesting
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
smarter men than I can calculate the pressure needed to blow that screw out. my inclination is that if the plug is threaded from surface to bore, it will hold just fine.
we drill relatively huge holes in the side of the barrel for vents, drums etc. without batting an eye.
the pressures are contained even whit the relatively few threads of the large drum. strength is dependent a lot on type of material and pitch of threads. those plug screws are generally whitworth threads, giving many teeth in a close length. = strength.
optically it sucks having that hole but not deadly. JM.002$
we drill relatively huge holes in the side of the barrel for vents, drums etc. without batting an eye.
the pressures are contained even whit the relatively few threads of the large drum. strength is dependent a lot on type of material and pitch of threads. those plug screws are generally whitworth threads, giving many teeth in a close length. = strength.
optically it sucks having that hole but not deadly. JM.002$
Hard to believe someone would drill holes in a barrel without setting a depth stop either on the drill press travel or drill bit to limit the depth of the hole for the desired screws length. Even just the drill bit itself can be set with one of the little doughnut shaped stops that lock on with a set screw to prevent drilling too deep into the bore.
Last edited:
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
I always thought that also. then the stop on my press slipped while i was daydreaming. nice little hole through the under rib and peeking through the bore of a nice colrain barrel. turned the 42 inch barrel into a 36 inch. stuff happens.
may have been a blessing in disguise. that little cherry stocked rifle stacks them on top of each other. especially when someone else is shooting it. gave it to the wife. Have had 3 offers for it(the rifle, not the wife) i have had to turn down.
Maybe if you made it a package deal there might be more interest.
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
not a chance! wife is rich! may be old and senile, but not dumb!
Shotgun loads are different than a PRB and ft sight is close to muzzle. OP's hole is right a Rear Sight area where pressure is a concern. Even then seem an area for snags and fouling buildup.
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
can't say how many Mauser 98's i have worked on that mirror that!
" mounted this scope and now i can't extract the case!??"
- Joined
- Oct 6, 2019
- Messages
- 109
- Reaction score
- 201
I’m really not sure I see a problem with a plugged threaded hole in a barrel.
A) The chamber end is threaded and plugged.
B) The percussion nipples are threaded and screwed into the barrel.
C)Percussion drums are threaded and screwed into the barrel.
D) Many flint guns have touch holes threaded and screwed in.
None of these seem to be of concern.
A) The chamber end is threaded and plugged.
B) The percussion nipples are threaded and screwed into the barrel.
C)Percussion drums are threaded and screwed into the barrel.
D) Many flint guns have touch holes threaded and screwed in.
None of these seem to be of concern.
Must have married into money.....
How about an minty all matching k98k ss totenkopf bringback1!!.
Of course she’s rich, she controls the ‘our’ money and the ‘her’ money…..
The ‘creative’ crowd can custom mount scopes without drilling and tapping any holes into the receiver or barrel.
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
Naw. she let me invest "our" money.
- Joined
- Mar 13, 2020
- Messages
- 7,482
- Reaction score
- 20,988
- Location
- On the Border in Idaho looking at BC
been a while since i saw that but i had judt got over the nightmares! thanks SD!
