- Joined
- Nov 16, 2009
- Messages
- 4,564
- Reaction score
- 8,144
It hasn’t been good for a long time when you’re reaching that point. Nipples AREN’T that expensive!
How often do you replace the nipple ?
- Thread starter kyron4
- Start date
Help Support Muzzleloading Forum:
Thank you, Bad Karma! I'll keep you in mind.Hi! I’m your new buddy! When do you start and do you want me to send you a priority box full of worn out nipples?
When looking at the Platinum nipples it's plain they're not completely platinum - probably steel with a platinum flash channel insert. My concern is ensuring there's no way the insert could shoot out the hammer side. But if BACO can do it without issues, I'm sure there's a way.
Does anyone know what alloy of Beryllium gets used for nipples? Beryllim bronze? Beryllium copper? Any others?
- Joined
- Nov 16, 2009
- Messages
- 4,564
- Reaction score
- 8,144
That’s exactly how they’re made. A small flange in the flat of the nipple is probably all, besides interference fit, which keeps the platinum bushing (lack of a better term) in place.
- Joined
- Nov 16, 2009
- Messages
- 4,564
- Reaction score
- 8,144
HahaConsider it the 'check engine' light
I check the oil. And drop a pin gauge into the orifice…just to check but every man to his humor, whatever seems to work without damaging the rifle is probably a good thing!
I think the Treso nipples are described as bronze, AMPCO bronze if that helps. Usually the factory supplied nipples are mild steel and are not very good to start with. Lots of advice to immediately go with stainless or start with Treso nipples.
- Joined
- May 23, 2019
- Messages
- 56
- Reaction score
- 71
I make platinum lined nipples for my Whitworth and Gibbs rifles. The small piece of platinum is silver soldered into a cavity drilled into the nipple. Never had one fail.
what's the OD/ID of this insert?
- Joined
- May 23, 2019
- Messages
- 56
- Reaction score
- 71
I was an industrial process control instrument tech before retirement. We used some instruments that had platinum filaments. As these units were replaced I got the filaments. I take one of these filaments and melt it into a ball which is about one eighth of an inch in diameter. The hole in the bead is the same size as the original hole, I can’t tell you the exact size without going out to the shop and checking my number drill bits.
I use the beryllium nipples, they last about 3-4 times longer than the others. I still have a few in my range box that I bought years ago.
- Joined
- Nov 16, 2009
- Messages
- 4,564
- Reaction score
- 8,144
I’m always astounded at the knowledge available on a foru such as this one. It’s truly amazing.
William - what did it take to melt the platinum?
- Joined
- May 23, 2019
- Messages
- 56
- Reaction score
- 71
i used a jewelers torch that uses oxygen and Mapp gas. Might could be done with Mapp gas with a needle flame..
New question, but along this same line:
I've got a Pietta 1860 army with Slix shot nipples. Came to me with them. The orifices are .037" and that seems pretty large. But they're all the same and don't look worn. Is this standard?
The threads in my search all come up with rifle nipples even though I specified pistol, so here I am. Have any of you measured the orifice on cap revolvers?
Also, if .037" is, in fact, a good size - why do they need to be so much larger than the .024" that's proper for a rifle?
I've got a Pietta 1860 army with Slix shot nipples. Came to me with them. The orifices are .037" and that seems pretty large. But they're all the same and don't look worn. Is this standard?
The threads in my search all come up with rifle nipples even though I specified pistol, so here I am. Have any of you measured the orifice on cap revolvers?
Also, if .037" is, in fact, a good size - why do they need to be so much larger than the .024" that's proper for a rifle?
Nipple configuration and orifice size are unique to each manufacturer. And if you ask each manufacturer, their nipple is the best.
The nipples I use in all of my rifles have an .032 orifice, Knights Red Hot. They work great.
Slix shot nipples work great with revolvers and are almost universally recognized as such.
So basically, revolver nipples, are different than, rifle nipples because of the shape of the fire channel and how they are used,,?
The only reason Slix Shot does that is because they work well.
Who said .024 is proper for a rifle? Just wondering?
The nipples I use in all of my rifles have an .032 orifice, Knights Red Hot. They work great.
Slix shot nipples work great with revolvers and are almost universally recognized as such.
So basically, revolver nipples, are different than, rifle nipples because of the shape of the fire channel and how they are used,,?
The only reason Slix Shot does that is because they work well.
Who said .024 is proper for a rifle? Just wondering?
Last edited:
I bought a pin gauge set just to document and compare wear on nipple holes. I build, shoot and compete quite a lot and want the best equipment I can get. Here is what I have found shooting normal match type loads which are basically volume grains that are around caliber size and up to 10-15 grains above. An example 40 caliber rifle = 40 grains to 55-60 grains. The standard metal nipple will start opening up within one or two range sessions and will progressively open. If I were to use one of these as my standard, I would replace it about every 100-150 shots (maximum) and always before any match. The Tresco Ampco nipple is better, but will start opening around 100 shots and will continue opening but much slower than standard metal. You can probably go to around to somewhere around 3-4 hundred shots before replacing. I have yet to have a Platinum lined nipple open up any at all and I have been shooting one for over a year averaging over 100 shots per week.
I have no idea what diameter hole is considered bad, but I do know that a hole that keeps opening up is not good. It is not consistent and that to me is bad.
I have found that standard metal nipples will start somewhere from .028 to .032 and will open very quickly.
I have found the Ampco to start around .028.
The Platinum nipples are around .025.
I have no idea what diameter hole is considered bad, but I do know that a hole that keeps opening up is not good. It is not consistent and that to me is bad.
I have found that standard metal nipples will start somewhere from .028 to .032 and will open very quickly.
I have found the Ampco to start around .028.
The Platinum nipples are around .025.
necchi - From the reading I've done (no personal experience) the figures that come up are .024" is optimum for a rifle nipple, and is worn out beyond .028". I believe it was Idaho Lewis said that, but others who compete found the same to be true. Orifice size is a game of going the smallest with good ignition. Velocity drops the larger the orifice becomes, so pressure is obviously being lost through the nipple. Evidently .024" is the optimum size.
Now, I wonder why revolver nipples aren't also .024"? Below .037" do the slix shots have inconsistent ignition? Why is .037" desirable in a revolver nipple, while in a rifle it's way beyond its prime and causing trouble?
I seem to recall that an oversize flash hole can cause a chain fire. Blowback through the nipple can set off neighboring loads.
Now, I wonder why revolver nipples aren't also .024"? Below .037" do the slix shots have inconsistent ignition? Why is .037" desirable in a revolver nipple, while in a rifle it's way beyond its prime and causing trouble?
I seem to recall that an oversize flash hole can cause a chain fire. Blowback through the nipple can set off neighboring loads.
Similar threads
- Locked
