I finished my first build...Kibler Colonial

Shop deals on ebay
the hawken shop
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I just got my first Kibler lock. It is a nice smooth lock. To avoid gouging the frizzen, you'll need to shim the back of the flint to get the proper strike angle. I was told by those who know that there are reasons for that, but I won't get into it in public.
 
EC121 said:
I just got my first Kibler lock. It is a nice smooth lock. To avoid gouging the frizzen, you'll need to shim the back of the flint to get the proper strike angle. I was told by those who know that there are reasons for that, but I won't get into it in public.
Click to expand...
You bring up a point I had been wondering about...At 1/2 cock there is a very large gap from flint to the frizzen...I have always understood that at that point minimal clearance was desired....1/8th inch or less (but not hitting). I dont see how you could shim it out that far and be secure in the jaws.
 
You don't shim it out. You shim the back of the flint up for more of a slicing action. However, the flint may hit lower, and you may need a longer flint or try it bevel down for a higher hit. It just takes some experimenting.
 
Just gorgeous, and your choice of limited line work well chosen. I also am looking at this Kibler Colonial kit. I figure it’s either the kids inherit or I have fun. Hope the kids keep their day jobs.
After reading your post, and others, the proper preparation of a fancy maple stock is tricker than I thought.
Ah, but to sport such a stunner at my local range, priceless!
 
Daveboone said:
I have a little bit of tweaking to do yet, but I think I can call it completed. I started it in mid august ...really just clearing the dedicated work area and figuring the plan of attack, needs ,etc. This is the first rifle "build" for me, and first attempt at anything of any detail or finishing. I found the inletting to be very tight, and the most time consuming. Chisels and files certainly are worth investing as much quality as you can. Also, ordering extra pin (music wire) stock to make easily removed ringed pins helps with the assembly, dissasembly and fitting. I am not quite happy with the locks finish. as cast its surface has a lot of variances in it, so a perfect smooth surface seems unlikely, but still obtaining a bit higher polish (then buff back) I think is in order. I really am happy with the barrel in the white. filed then sanded down to 400. I messed around with an old barrel sampling browning, but was never pleased. The brass I filed/polished and sanded to 400 then scotch brighted, then 0000 steel wooled. I aqua fortised . That was touchy. I did have a couple light scorches which i sanded out and easily re-did. FYI....not as much heat was needed as I thought. I was making a small priming horn to match the rifle (main horn next project) with tger stripe maple plug. I also AF the plug, and the heat from our pellet stove blower was warm enough to make it blush, the plug easily held by hand in the process. Once I had the riflef wood almost finished I decided I didnt like the wood behind the tang or the tapers behind the lock and screw plate, so ended up re-shaping those three areas over, and refhinished. I probably could have avoided that by earlier in the process damping the wood to bring out the contours more. Lessons learned. The aqua fortis is very forgiving to reblend. I finished with Kiblers stock sealer. seriously, probably about twenty coats in some areass, with steel wool after each drying, then a quick wipe with a lightly moistened cotton rag with acetone. I was very pleased when the wife walked by and was somewhat mesmerized by the 3 D affect of the striping. She stroked the wood and stated..."it feels so soft like my fingers are sinking in to it". I was pretty pleased with that...I am usually a "coat of barn paint and we are good" kind of guy.
The stock had me a bit frustrated. There is a section of wood near the butt plate that has little to no figure to it, that extends through to the other side. It looks very out of place, but it is what it is.
I wasnt brave enough to try any inletting, but decided a few simple strait lines were tough to screw up, so added a couple to both the cheek piece and the top of the patch box cover. I was pleased with how they looked. Another small detail I experimented with was heat bluing the rear sight and trigger plate. Both turned out great, a beautiful blue/black. Simple to do. I was considering doing the trigger also, but was concerned of the contact surface /sear area getting messed up.
Now to wait for the range to warm up.
Click to expand...
If this is your first build I can't wait to see your second one! Very nice job my friend!
 
Nicely done! Having recently finished a Colonial, I found it was a sneaky "gateway drug". I'm now building an assemblage of parts from a Sitting Fox kit...Lancaster in .54. It requires a LOT more fitting and is a step closer to building from a plank, which I'd like to try next. So now...what's YOUR next build?
 

Similar threads

Tumbledown
Early American VA/PA Inspired Rifle- my first true kit build
Replies
3
Views
389
ckwilli
ckwilli
L T Grey
My Recent Rifle Build
2
Replies
33
Views
3K
shorthair
S
aprayinbear
  • Locked
SOLD Kibler Woodsrunner .50 cal for sale
Replies
6
Views
636
AZ Muzzleloaders
AZ Muzzleloaders
tjiann
My Kibler Colonial
Replies
12
Views
2K
James Kibler
J
G
My first Kibler Assemble
2 3
Replies
52
Views
4K
Psycho Mike
Psycho Mike

Latest posts

Back
Top