• If you have bought, sold or gained information from our Classifieds, please donate to Muzzleloading Forum and give back.

    You can become a Supporting Member which comes with a decal or just click here to donate.

SOLD Original Parlor Gun ca. 1870

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Status
Not open for further replies.
Joined
Oct 5, 2021
Messages
1,339
Reaction score
1,751
Location
SE PA
Offering a Wurfflein Parlor Rifle, made in Philadelphia PA around 1870. Maker-marked on top flat and CREEDMOOR PAT C APP'D FOR on flat below.

The "barrel" is exactly 24 inches long, however the working section is 4.75 inches and about .17 caliber. The rifling is sharp and bore is bright. I don't have a jag or brush small enough, but I suspect the few spots in the bore will clean better. It is fired with a percussion cap placed over a nipple through an opening in the bottom of the barrel. The nipple is in very good condition. Number 11 caps fit a little loose, likely 10's will fit better. LOP is 13.75 inches. Wrist is checkered and all metal has fine engraving.

A couple dings in the wood and a little patina to the engraved furniture, but the gun is in excellent shootable condition at 150 years old. A beautiful original gun from a time of entertaining at home with some indoor shooting and friendly competition. Parlor guns were made between 1870 and 1920, providing economical arms for social clubs and creedmoor matches. A well-to-do gentleman's gun. Early guns, like this one, use a percussion cap as the propellant, while later guns were breech-loaded and adopted small caliber cartridges.

Smoking jackets, cognac and shooting 17 caliber pellets in the parlor, but it all ends with WWI and prohibition...

Asking $800 shipping included in the USA. Check or money order. PM for details.
 

Attachments

  • PXL_20240427_012823465.jpg
    PXL_20240427_012823465.jpg
    1.5 MB
  • PXL_20240427_012836884.jpg
    PXL_20240427_012836884.jpg
    548.2 KB
  • PXL_20240427_013003801.jpg
    PXL_20240427_013003801.jpg
    2.9 MB
  • PXL_20240427_013010181.jpg
    PXL_20240427_013010181.jpg
    3 MB
  • PXL_20240427_013029616.jpg
    PXL_20240427_013029616.jpg
    2.1 MB
  • PXL_20240427_013039468.jpg
    PXL_20240427_013039468.jpg
    2.8 MB
  • PXL_20240427_013155962.jpg
    PXL_20240427_013155962.jpg
    3.4 MB
  • PXL_20240427_013201359.jpg
    PXL_20240427_013201359.jpg
    2.9 MB
  • PXL_20240427_013211213.jpg
    PXL_20240427_013211213.jpg
    2.3 MB
  • PXL_20240427_013320795.jpg
    PXL_20240427_013320795.jpg
    3.5 MB
Details and photos of the actual shooting part of the barrel. Video as well, though removing should not be necessary except for periodic deep cleaning.
 

Attachments

  • PXL_20240427_004117836.jpg
    PXL_20240427_004117836.jpg
    1.9 MB
  • PXL_20240427_004126952.jpg
    PXL_20240427_004126952.jpg
    3.1 MB
  • PXL_20240427_010224509.jpg
    PXL_20240427_010224509.jpg
    1.9 MB
  • PXL_20240427_010353304.jpg
    PXL_20240427_010353304.jpg
    1.8 MB
  • PXL_20240427_010555561.jpg
    PXL_20240427_010555561.jpg
    2.3 MB
  • PXL_20240427_010612628.jpg
    PXL_20240427_010612628.jpg
    2.8 MB
  • PXL_20240427_011247038.jpg
    PXL_20240427_011247038.jpg
    4.5 MB
  • PXL_20240427_011253201.jpg
    PXL_20240427_011253201.jpg
    4.1 MB
  • PXL_20240427_011259684.jpg
    PXL_20240427_011259684.jpg
    2.2 MB
  • PXL_20240427_011455979.mp4
    31.7 MB
Last edited:
Operation is:
Load through the muzzle a BB or pellet.
Cock the hammer, slide the operating rod to the rear using a finger through gate in bottom of barrel, fit a percussion cap on the nipple.
Take aim...
 

Attachments

  • PXL_20240427_013120747~2.mp4
    36.4 MB
For the buyer or seller - this looks like an absolutely cool thing and I'd love to see a nice write up or maybe video showing it, firing, etc. at some point in the future!
 
For the buyer or seller - this looks like an absolutely cool thing and I'd love to see a nice write up or maybe video showing it, firing, etc. at some point in the future!
I snapped a couple #11 caps in it, but don't have a thin enough ramrod to push in a patched BB (only have copper plated and they're a tad undersize without a patch). A 32 is fiddly enough for my clumsy fingers...but definitely a cool gun.
 
Status
Not open for further replies.
Back
Top