• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Rolling papers for combustible cartridges?

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I use hair curling papers and nitrated coffee filters with good success. Here is a picture
P1030556.JPG
P1030557.JPG
using nitrated coffee filters. Paper cartridges of old were held together using Waterglass which you can buy on the internet. I tried it - it is a bit fussy as it is applied with a small artist brush. I prefer the glue stick method.
 
Last edited:
I've seen it suggested to use ol' Zig Zags or other brands of roll-yer-own cigarette (or, uh, other plants) paper to make combustible cartridges for revolvers. Anyone tried this?
That is what I use. Cigarette papers work fantastic and are dirt cheap to buy. They last forever. Burn completely upon ignition.
 
I've seen it suggested to use ol' Zig Zags or other brands of roll-yer-own cigarette (or, uh, other plants) paper to make combustible cartridges for revolvers. Anyone tried this?
Yes but not ZigZag
I use Bee Organic Hemp papers for RB's -- strong, thin, and no need to nitrate (1 1/4 inch size)
I use RAW Organic Hemp for conicals with Pyrodex 30 Gr pellets -- Need 1 1/2 size. As the BEE, it is strong, thin, and no need to nitrate.
For both you can add a wad if you want... or not. Adding a wad supposed to improve groups and decrease fouling but haven't shot enough of them to know for sure in my 1858 yet
When rolled, both get dipped in melted SPG Lube or the lube from Guns of the West. If lubed wad added I do not grease over the projectile.
Use caps that are tight to prevent chain fire -- so I am told
 
Holding a paper cartridge by the balls lololol with twisted end (with a dab of glue) so it holds better at range before I cut it off for loading. That's my bottle of potassium nitrate in solution and I am dipping them (very quick in and out ) briefly then dry them. It is just a labour of love for them old .44's.. The gun is an original Rem 1858 the finished loads are at back. Conical has around 28-29 grains. I lube them as well. Enjoy the shoot smells like victory to me.
 

Attachments

  • DSCN0160.JPG
    DSCN0160.JPG
    832.4 KB
  • DSCN0158.JPG
    DSCN0158.JPG
    821.3 KB
  • DSCN0159.JPG
    DSCN0159.JPG
    831.9 KB
  • DSCN0161.JPG
    DSCN0161.JPG
    891.4 KB
  • DSCN0153.JPG
    DSCN0153.JPG
    812.1 KB
  • DSCN0152.JPG
    DSCN0152.JPG
    851.6 KB
  • DSCN0148.JPG
    DSCN0148.JPG
    520.8 KB
I've used RAW brand papers with good results. I have made several dozen paper cartridges so far and I have never had an issue in my 1862 Pocket Police. I have never found that they need to be nitrated.
One of my pistols is the 1862 police .36. The cigarette papers work great without nitrating them. super handy.
 
Here is my method for rolling tubes. in order from top left.
Papers, cut the pack in half,put on a dowel (or a marker pen right size) lick glue strip and glue ,remove and there is your tube . The last one has a .454 ball in it. I do glue mine in for strength and this is just to show. Once you get a rythmn doing it the time just goes by and next thing ya know you blastin away.
 

Attachments

  • DSCN0163.JPG
    DSCN0163.JPG
    824.5 KB
Interesting! I've heard of folks using thinned out nitrocellulose glue, like Duco Cement, to seal up combustible cartridges but it sounded fiddly enough that I hadn't tried it. Any specific nitrocellulose lacquer you'd recommend? Maybe I'll give that go with my RAW papers. Thanks for sharing that tip @Billywfe !
I use the watco
 

Attachments

  • 16783949818037950266069303997606.jpg
    16783949818037950266069303997606.jpg
    1.9 MB
I need to figure out how to make a template.
Tarponstalker, make your former first, then make your template to fit it. Here's a sketch of a pretty good former for 44s. I whittled mine out of a maple branch, coated it liberally with paraffin, heated. My first go round I wrapped a hair curler paper around the former and marked it with a pen, giving it about a ¼" overlap. I twist mine over the ball, so I use the whole paper. I cut the end piece with a ¾" punch, but square pieces work fine. I don't use a base block, I put them on the end of the former and glue the cartridge paper to it.
Now I make them like in the video I posted in post #18 using the 3in1 cellulose glue.
I know I said I wanted to do a thread on what I've been doing, but I don't have anything to add to the xlent posts that are already up. Those are some fine looking cartridges, folks, I'm thoroughly enjoying this thread, keep em coming!
 

Attachments

  • IMG_20230309_154037_01.jpg
    IMG_20230309_154037_01.jpg
    510.1 KB
  • IMG_20230309_153848_02.jpg
    IMG_20230309_153848_02.jpg
    508.1 KB
  • IMG_20230113_124430.jpg
    IMG_20230113_124430.jpg
    3.2 MB
I've seen it suggested to use ol' Zig Zags or other brands of roll-yer-own cigarette (or, uh, other plants) paper to make combustible cartridges for revolvers. Anyone tried this?
Well, that’s one way to explain it if your wife finds your rolling papers… oh and that hollow glass thing is a “sculpture “…
 
Nitrated adds a flash that helps scare the enemy on the other side and impresses the yokels. Too much time on my hands I am an old man must have been alive in civil war I feel like that some days lololol.
 
Tarponstalker, make your former first, then make your template to fit it. Here's a sketch of a pretty good former for 44s. I whittled mine out of a maple branch, coated it liberally with paraffin, heated. My first go round I wrapped a hair curler paper around the former and marked it with a pen, giving it about a ¼" overlap. I twist mine over the ball, so I use the whole paper. I cut the end piece with a ¾" punch, but square pieces work fine. I don't use a base block, I put them on the end of the former and glue the cartridge paper to it.
Now I make them like in the video I posted in post #18 using the 3in1 cellulose glue.
I know I said I wanted to do a thread on what I've been doing, but I don't have anything to add to the xlent posts that are already up. Those are some fine looking cartridges, folks, I'm thoroughly enjoying this thread, keep em coming!
This how I do it. Works great. Rip the paper off the ball after seating it in cylinder.
 
Back
Top