Specific rifling depth for hollow base/flat base muzzloader bullets

[SolidLeadSlug]

Due to difficulty locating a mold maker who can make me a hollow base mold for my swiss feldstuzer, I'm wondering if using a flat base mold will be reasonable.

The rifles groove depth is around
0.007 and mat or may not be progressive depth.

The bulholzer bullet is a 289g hollow base paper patched bullet of .399 diamter. When loaded, it will be patched to .408-409.

I've found a .410 300 grain grease groove bullet that I am hoping has sufficient weight to be swaged i to the deep grooves. It will be cast of pure lead.

My question is will a flat base bullet be able to bump up to a deeply rifled bore or should I hold out for a hollow base bullet that is paper patched

 

[Gollywomper]

My small amount of experience thinks you will be fine. I am shooting a .50, my barrel measure .499/.517. I size my bullets to .5005. They seem to seal up just fine with a overpowder wad.

 

[SolidLeadSlug]

My small amount of experience thinks you will be fine. I am shooting a .50, my barrel measure .499/.517. I size my bullets to .5005. They seem to seal up just fine with a overpowder wad.

What rifle and load are you shooting exactly? That's good to hear your having good results. The Swiss feildstuzer and infanteriegewehrs when through 3 variations of bullet. A linen patched flat conical, PP compression and finally more or less a .399 minie style with paper patch.

 

[Gollywomper]

I am shooting a traditions mountain rifle, with a 418 grain grease groove bullet. These are poured with a 40-1 alloy, slightly harder than pure lead.

There is a lot of pressure on the base of a bullet during ignition. However nobody know for sure until they experiment with loads and variations of such.

 

[pchwcf50110]

Have you tried Steve Brooks of Brooks Mold? He custom makes all kinds of hollow point, hollow base, nose pour, base pour molds.

 

[French Colonial]

Have you tried Steve Brooks of Brooks Mold? He custom makes all kinds of hollow point, hollow base, nose pour, base pour molds.

He is not cheap, but his quality is excellent.

 

[SolidLeadSlug]

He is not cheap, but his quality is excellent.

I ordered a mold from him and he demanded a ridiculous amount of money for it without even giving me a quote after making it. My lyman mold is just as good as his stuff

 

[French Colonial]

I ordered a mold from him and he demanded a ridiculous amount of money for it without even giving me a quote after making it. My lyman mold is just as good as his stuff

No....No it is not.

You can give the land and groove dimensions of your barrel to Steve and he will custom make a mold for your barrel and the bullets from his molds will be perfect.

He is one of the reasons I was able to shoot master class in BPCRS.

 

[nkbj]

Due to difficulty locating a mold maker who can make me a hollow base mold for my swiss feldstuzer, I'm wondering if using a flat base mold will be reasonable.

The rifles groove depth is around
0.007 and mat or may not be progressive depth.

The bulholzer bullet is a 289g hollow base paper patched bullet of .399 diamter. When loaded, it will be patched to .408-409.

I've found a .410 300 grain grease groove bullet that I am hoping has sufficient weight to be swaged i to the deep grooves. It will be cast of pure lead.

My question is will a flat base bullet be able to bump up to a deeply rifled bore or should I hold out for a hollow base bullet that is paper patched

Hot doggies!
Here's molds for the solid base and hollow base versions of the Buholzer bullet currently available to be ordered. Mold numbers 40-289M and 40-289MN.
https://accuratemolds.com/catalog.php?page=14#catalog-anchor

 

[SolidLeadSlug]

Hot doggies!
Here's molds for the solid base and hollow base versions of the Buholzer bullet currently available to be ordered. Mold numbers 40-289M and 40-289MN.
https://accuratemolds.com/catalog.php?page=14#catalog-anchor

Unfortunately they do t have a hollow base and would cost me another 175 to have a base plug made.