Don't even know if parts are available, but looking at my vintage Lyman sizer/lubricater this afternoon, thought it might be possible. Heck, might even be a commonly used practice to run cast projectiles through it for my M/L's? Will it work?
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Using Sizer/Lubricater For Cast Projectiles?
- Thread starter sheriff john
- Start date
Help Support Muzzleloading Forum:
longcruise
70 Cal.
I do it with some that are too big. 501 for 50 and 451 for 45.
Might be more economical to use the Lee push through sizers.
Might be more economical to use the Lee push through sizers.
- Joined
- Jan 9, 2017
- Messages
- 1,110
- Reaction score
- 1,230
Works for me I run 2 Lyman 450 s one for center fire (not used much)and the other used every day .Could not get thru the day without it/Ed
Thanks for the fast replies. Just like old guns, I enjoy "vintage" tools & reloading stuff. Some's been unused for many years, but they're as good as they ever were - sometimes better than newer ones. Should perhaps get better "coverage" with the lubricater than glopping by hand, I assume?
Sparkytfl
32 Cal
Do you mean for minie bullets? I Have a pair of Lyman 45s, one full of beeswax/lard, and one with smokeless lube. S & S Firearms and/or Lodgewood sell sizing dies up to like .600 so you can use it for a civil war Springfield or whatever.
I've been using a Lyman Sizer/Luber for .58 minies for years now and just restored a vintage one for use with my Maynard, Sharps, .50-95 & .50-70 bullets. Dies are readily available as Sparkytfl posted and there are so many of them around I have never worried about parts but have never needed any either.
Have to get to digging to see exactly what I have. Lyman .58 minie, for sure. Experimented with .45 and 50 20 years ago and a couple of original Colt molds. Pretty well have always shot patched round balls, but it's winter and I'm bored. A fellow can accumulate a lot of stuff over 50 years.
I should add they are a bear to clean out and change lube in. I recommend one set up for each type of lube you'll use.
user 48702
Richard Turner
- Joined
- Sep 17, 2020
- Messages
- 1,142
- Reaction score
- 2,799
I have an RCBS lube/sizing press with heater and I use the current made Lyman size dies. You can still buy them from Midway, Midsouth, and other sources and they will fit your press. I have a few conicals that I run through the sizer.
- Joined
- Jan 9, 2017
- Messages
- 1,110
- Reaction score
- 1,230
Don't size minis /maxis or any hollow base bullet or the Lee R.E.A.L. as they are meant to be used with pure lead and engrave upon loading /bands vary, base narrow and increase towards the nose /Hollow base walls flair out to engage rifling. All those types get ruined by your attempts at sizing hollow based sized will weaken /thin walls and they then fail to engage great for shooting a line of attackers (someone )will be unlucky but accuracy was never the intent ,just rate of fire/Ed
Last edited:
Almost everyone in the N-SSA sizes their minies. Sizing them is the key to accuracy. They must be able to be loaded quickly and yet be close enough to the bore size to engage the rifling when fired. Too small and they won't do that and too large and they need to be pounded down the barrel. I have some molds that cast a thin skirt (Rapine) and some that have a new base plug to produce a thin skirt. None of these give any problems.
