• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Woodsrunner build help....

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

mrfritz44

32 Cal
Joined
Jan 21, 2024
Messages
34
Reaction score
23
Location
PA
So, the Woodsrunner came together like a charm recently with one exception. While installing the nose cap one of the brass screws sheered off. I received a new cap today but without screws so I headed down to the local hardware store to figure out what I could buy that would allow be to finish the build phase this weekend. In the process of trying many screws in the old and new caps, being very careful not to force any one screw, the closest we came to deducing the thread and pitch was 4-40. This seemed to be corroborated in another thread in this forum where another person also sheered off their nose cap screw.

That all said, any 4-40 we tried would only get about flush with the opposite side of the hole and then stop on both caps.

Before I screw up a second nose cap, no pun intended, who knows the size of these brass screws?
 
So, the Woodsrunner came together like a charm recently with one exception. While installing the nose cap one of the brass screws sheered off. I received a new cap today but without screws so I headed down to the local hardware store to figure out what I could buy that would allow be to finish the build phase this weekend. In the process of trying many screws in the old and new caps, being very careful not to force any one screw, the closest we came to deducing the thread and pitch was 4-40. This seemed to be corroborated in another thread in this forum where another person also sheered off their nose cap screw.

That all said, any 4-40 we tried would only get about flush with the opposite side of the hole and then stop on both caps.

Before I screw up a second nose cap, no pun intended, who knows the size of these brass screws?
Just call Kibler. They will help you.
Larry
 
Yep, tried, and emailed, and texted from the hardware store. They're busy and I get it, so I thought I'd try here.
Try a phone call. They're notoriously slow in responding to emails. They will respond, but they get so many, it may take up to a week. Since your problem involves a build issue, I think leaving a phone message will get you a quicker answer than an email.
 
Thanks very much Buff1958 and 2shots. I'll head back to the hardware store today and try the 4-40 screws again after a quick borrowed tap.

The screws were acting like they were imperial sized right up until they came flush to the opposing side, and then locked up like I was forcing a metric sized screw. The fact that these caps are $26 bucks to replace forced an abundance of caution and so your confirmation of size makes it easier to move forward, especially since any forced solution would be a scar on the gun I would see forever even if it was hidden under the barrel.
 
This issue was resolved by using a 2 inch 4-40 stainless screw with light oil to tap the cap holes in an improvised way. Once I new I was dealing with 4-40 size screws and wouldn't totally be mashing the threads it was pretty straightforward to attach the cap.

What's funny is that in Jim's video he also has a little trouble starting one of the screws. Maybe some degree of polishing after the tapping rounded over the brass and is increasing the chance of sheering these delicate screws? Anyway, good to be aware of this since at least one other person experienced the same.

Thanks again for confirming the size.
 
I hope Jim sees this. He always addresses recurring problems his customers have, especially when more than one person mentions. I remember having a problem with pinning the cap. Someone here told me how to make it work.
 
Back
Top