Just wondering if most folks have THE BRASS BRUSH IN THEIR CLEANING RITUAL. I ALWAYS HEAR I SWAB IT WITH THIS OR THAT AND NEVER HEAR ABOUT A BRUSH. I MYSELF ALWAYS USE ONE AFTER THE PATCHES COME OUT CLEAN AND THEN I WET IT DOWN AGAIN, AND MAN IT LOOKS LIKE STARTING ALL OVER . To ME THAT IS CLEAN; JUST WONDERING .
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
cleaning brush
- Thread starter mrd
- Start date
Help Support Muzzleloading Forum:
I tried a brass brush once and didn't think I was going to get it out of the barrel.
Tried a brush forty years ago, threw it out
There has been a lot of passionate discussions about using a bore brush. This is likely going to cause some flames.
If you use one, just remember to turn it CW 1/8 turn BEFORE trying to back it up, so the bristles release.
If you use one, just remember to turn it CW 1/8 turn BEFORE trying to back it up, so the bristles release.
If you choose to use a brush make sure you ONLY use a brush that is locked to the shaft and use it with a solid range rod NOT the wood rod on the gun, and finally like O'Brian said give it a turn before retracting. Cheap brushes and rods account for 99% of issues of a stuck brush.
Yea got that stuck down there good. I cried a little fighting getting it out.
Never used one since.
Never used one since.
- Joined
- Mar 23, 2021
- Messages
- 2,826
- Reaction score
- 6,056
Very rarely use a brush but...
As discussed above, turn it to get the bristles to lay down somewhat. I usually do this before I even have the brush completely in the bore and continue to turn it all the way down. Once you get the bristles to flex they usually continue to do so quite easily.
This is of course using a sturdy metal range rod at home with the gun secured in the vise.
I only use it when working on the most stubborn fouling/rust, as in the basket case rifle I bought last spring, for routine cleaning it is not needed.
As discussed above, turn it to get the bristles to lay down somewhat. I usually do this before I even have the brush completely in the bore and continue to turn it all the way down. Once you get the bristles to flex they usually continue to do so quite easily.
This is of course using a sturdy metal range rod at home with the gun secured in the vise.
I only use it when working on the most stubborn fouling/rust, as in the basket case rifle I bought last spring, for routine cleaning it is not needed.
- Joined
- Jul 8, 2019
- Messages
- 3,160
- Reaction score
- 5,676
Water, soap and snug patches! This is all you need to clean a rifle.
I normally use a brush as one of my cleaning steps, but it's a one-caliber oversize poly brush. Very seldom see any need for brass in cleaning black powder. Maybe if a guy waited too long before cleaning .... hah.
Soap, water and patches for the bore. I do use a small, about 3/8", brass brush and scraper to clean the firing chamber that Investarms have.
Brokennock
Cannon
As has been said, you can use a brush if you feel it is necessary as long as you use the correct brush and give it that little CW turn before pulling it out.
Some say it is completely unnecessary,,, but some say a lot of things.
Our late friend @Flehto used a brush on an inverted/muzzledown rifle instead of wet swabbing between shots, this broke up and allowed to fall out any caked on residue. It always made sense to me, even of the muzzle down thing isn't practical for everyone. I recently have been doing similar on a certain part on a particular unmentionable, dry brushing dry residue/carbon,,,, works much better than turning it to liquid 1st then trying to mop up.
Get the propper tools and try it for yourself.
Some say it is completely unnecessary,,, but some say a lot of things.
Our late friend @Flehto used a brush on an inverted/muzzledown rifle instead of wet swabbing between shots, this broke up and allowed to fall out any caked on residue. It always made sense to me, even of the muzzle down thing isn't practical for everyone. I recently have been doing similar on a certain part on a particular unmentionable, dry brushing dry residue/carbon,,,, works much better than turning it to liquid 1st then trying to mop up.
Get the propper tools and try it for yourself.
On an unmentionable bud..
It's a little easy. Just shoot it till your barrel is not burning you hot but you know hot. Then Clean it.. you can still run a dry brush first but i don't think you'll need it at all.
Everything cleans right out.
It almost does too good a job.
It's annoying dealing with patches. Cleaning rod. Small caliber. Just pull a bore snake threw and go home clean the rest.
Last edited:
Never tried it myself. Chore boy?
Use a smaller brush with that... would it get stuck?
That brush was a surprise for me. Thing went down easy.
Use a smaller brush with that... would it get stuck?
That brush was a surprise for me. Thing went down easy.
Erwan
45 Cal.
After shooting clean your rifle before the residues become hard and, after and at home, clean and oil it with a normal process (water/soap, Ballistol/water, Parker Hale oil, patches, etc.). That'll be largely sufficient, if you want to use a brush, take a plastic brush and try to forget the brass: sometimes it could be hard to remove that brush from the barrel...
Back in the day when I first shot a muzzle loader I tried using a brush-- well because that's how you clean guns, right?
The brush got stuck so hard I had to remove the breech. Never again...
Removable barrels are put breech end in a bucket of water and dish detergent and swabbed (pumped, more like it..)with a tight patch. Pinned barrels get a magnetic doo-hickey over the flashhole with a tube running into the bucket. They get perfectly clean that way.
If I feel the need to polish to bore I use a square of extra-fine scotchbrite pad over an undersize jag.
The brush got stuck so hard I had to remove the breech. Never again...
Removable barrels are put breech end in a bucket of water and dish detergent and swabbed (pumped, more like it..)with a tight patch. Pinned barrels get a magnetic doo-hickey over the flashhole with a tube running into the bucket. They get perfectly clean that way.
If I feel the need to polish to bore I use a square of extra-fine scotchbrite pad over an undersize jag.
Banjoman
Eager to learn and willing to teach.
Tow on a worm fits all bore sizes.
- Joined
- Jul 8, 2019
- Messages
- 3,160
- Reaction score
- 5,676
