Another Walker adjustment

M. De Land said:

Still learning the nuances of the new Uberti Walker I acquired last year I recently noticed that the trigger nose is contacting the half **** notch as the hammer falls with the addition of the action shield apparently. My guess of the cause is perhaps the added weight on the hammer or possibly interference fit of the shield in the hammer mortise or to heavy of a trigger return spring.
I'll post back with a cause and remedy when I get it all sorted out.

Click to expand...

M. De Land said:

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.

Click to expand...

M. De Land said:

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.
I really like the loading lever latch as it works very smoothly and locks the lever very securely in place with the most leverage possible, at it's tip.

Click to expand...

bpd303 said:

I've never seen that type of loading lever latch, did it come from Uberti like that. Interesting to say the least.

Click to expand...

M. De Land said:

I may at some point just remove the Walker spring entirely and re-engineer/alter to a Dragoon type flat spring arrangement as the Walker spring has always felt mushy in the middle of the stroke to me. A single leaf flat spring will have a faster response time than does the original Walker design with the two legs and turn back V and very likely make a marked improvement in hammer speed.
I'll take photos and post them if I decide to make the alteration.

Click to expand...

45D said:

Have you reduced the cam height and blended the bottom of the cam to that of the hammer surface? That will make a smoother transition for the bolt arm (which should have a polished arc for the transition as well) and impart less drag on the hammer.
Of course polishing the contact surfaces between the main spring and radius in the hammer will make an improvement. This contact patch moves from the rear of the radius towards the middle as the hammer is cycled back. Therefore the contact patch moves to the rear of the radius cut as the hammer moves forward, which actually speeds up the hammer with a camming effect. Watching this happen is exactly where I got the idea of bending the very end of flat mains upwards to speed up the hammer right at the end of its travel.
Just some food for thought . . .

Mike

PS You could also remove some weight . . .
View attachment 363227

Click to expand...

M. De Land said:

I reduced the width (not thickness) of the trigger return spring and re-contoured (lowered) the nose of the half **** notch which greatly reduced the trigger nose contact with the half ****. It looks like the trigger return spring was so stiff it was pulling back the trigger nose, contact release length from full **** into making a bounce contact with the half **** nose as it passes over in full cycle. I may still add a leverage block into the curve (turn back) of the main spring to increase it's strength and thus speed as I learn the nuance and balance of fine Walker tuning.
I really like this pistol and the add on's installed.
It doesn't seem to need a cap rake but it's not out of the question if problems arise. Most interesting gun to work on and experiment with.
I really like the loading lever latch as it works very smoothly and locks the lever very securely in place with the most leverage possible, at it's tip.

Click to expand...