I like to paint the underside of my barrel and barrel channel with bees wax. I pull my barrels now once aver few years and that treatment keeps them clean.
Cleaning Kibler Woodsrunner?
- Thread starter CatchingChrome
- Start date
Help Support Muzzleloading Forum:
I HAVE used it to brown barrels.
I looked it up. Peroxide is a bleaching agent that can indeed be corrosive to metal and wood and wood finishes. Best to use diluted. I've always said there is something to be learned here every day. Actually I've never used it
I looked it up. Peroxide is a bleaching agent that can indeed be corrosive to metal and wood and wood finishes. Best to use diluted. I've always said there is something to be learned here every day. Actually I've never used it
I remove mine about once a year and put a heavy coat of wax under the barrel. Then once it is back together, I put a couple of coats of wax on the whole gun making sure to get it in where the barrel meets the stock to form a water tight seal. I shoot 4 or 5 days a week and figure I would wear out the pin holes pushing them out 5 times a week
A friend suggested using windshield washer fluid, mostly water anyway. With patches several times till they came out clean. A scraper for the breach. Then I used balistol worked very well on my colonial
Marc H
32 Cal
What is the cleaning method described in the Kibler Manual?
Wouldn't that be the best place to find accurate info?
Marc
Wouldn't that be the best place to find accurate info?
Marc
I don't ever take barrels off.
I've been using the magnetic flusher sold by a member in here, davec2, and it works really well: LINK TO FLUSHER
Here's the way I clean my rifles - just my 2c, YMMV:
1. I pull the lock and clean it with straight Ballistol
2. Place the magnet over the hole, blow thru it to make sure youre over the vent.
3. Place the tube clunk in hot water w/Dawn
4. Orient gun muzzle low w/vent down. Pump back and forth w/patches until clean. Make sure dont knock magnet off-center.
5. Real good generous water flush shot of WD40 after.
6. Dry patch and QUICKLY, to avoid flash rust, swab with RIG patch with a shot of WD40 to saturate and dilute a little.
7. Re-assemble, wipe all over gun w/Ballistol rag, give 'er a good rub down with an old t-shirt, store gun muzzle down for a day or 2.
I've been using the magnetic flusher sold by a member in here, davec2, and it works really well: LINK TO FLUSHER
Here's the way I clean my rifles - just my 2c, YMMV:
1. I pull the lock and clean it with straight Ballistol
2. Place the magnet over the hole, blow thru it to make sure youre over the vent.
3. Place the tube clunk in hot water w/Dawn
4. Orient gun muzzle low w/vent down. Pump back and forth w/patches until clean. Make sure dont knock magnet off-center.
5. Real good generous water flush shot of WD40 after.
6. Dry patch and QUICKLY, to avoid flash rust, swab with RIG patch with a shot of WD40 to saturate and dilute a little.
7. Re-assemble, wipe all over gun w/Ballistol rag, give 'er a good rub down with an old t-shirt, store gun muzzle down for a day or 2.
Last edited:
For 25 years or more I've used the Murphy's oil soap, rubbing alcohol, hydrogen peroxide mixed equally as my cleaning solution. It cleans quickly and I've never had corrosion problems. After trying it a couple times I did find I could not use it to clean the exterior of the barrel--it does remove browning.
Lots of various cleaning concoctions. I've used various mixtures over the years, but settled on just using warm water with a little Dawn. I do have one of the clamp on pump devices, but rarely use it. I remove the lock and clean. I put down a folded paper towel and lay the rifle touch hole down on the paper towel to catch residue. Wet patch until clean. When cleaned and dry I first squirt a little WD40 in the touch hole to capture any moisture I may have missed, run another dry patch, then run a patch with a rust inhibitor.
Exception is if I have used conicals. Then same procedure, but will occasionally scrub out lead residue with JB Bore paste.
Exception is if I have used conicals. Then same procedure, but will occasionally scrub out lead residue with JB Bore paste.
jtkerk
40 Cal
- Joined
- Feb 11, 2022
- Messages
- 170
- Reaction score
- 76
I agree never remove barrels to clean. No need. Clean as many people have said above.
A friend introduced me to using windshield washer fluid. Works great
I also use the Magnetic tube device on my Touch hole and it works Great! I remove the Lock then clamp the gun to be cleaned in my Padded Pattern makers vise upside down horizontally, so the sites are facing down. This way if the tube leaks, it does not run down the stock. But it never does the magnet on. It is strong and works great and I put my pale of water on a stool just below it with room, temperature, water, and a little bit of dawn
I'm going to migrate over to room temp water instead of hot to try to mitigate flash rusting. We'll see how it works.
Assuming there was s a recess in the breach plug. It would be nice to know the inner diameter. This would allow the use of a scraper for maximum cleaning. That is if the touch hole liner doesn’t protrude in the the recess.
TerryK
40 Cal.
I use simple green and water as a soap, and balistrol and water as a patch "scrubber", balistrol as a final light oil. Works well, easy, no rust.
I do the initial flush/clean at the range, and the rest at home. Again, easy to do.
I do the initial flush/clean at the range, and the rest at home. Again, easy to do.
Go point, if the touch hole liner is protruding into the barrel that is not good! It would need to be D breached and ground down flush with the barrel diameter.
True. I don’t have the issue. Though I admit I had a hook breach in mind when I made the comment. (New project)
Similar threads
- Locked
