I’m at a loss

Daytime Smoker · Friday at 9:30 PM

So, I got this traditions deer hunter as a project from my father. Dad had an optic and had it drilled and tapped. No big deal. I took the scope and rings off. What I can’t figure out is how to change it back to a normal nipple. He had a mag spark and I’m not a fan of those anyway. Not that I have anything against them, just not my style. Anyway, how in the heck do I change it back? Here are a few pics after I got the mag spark nipple or topper off. Do I try to take the drum off? Like I said ya can’t beat basically free. And it’s a muzzy, so I’ll take those all day any day. Plus, I have a soft spot for something that came from my dad. Any help would be appreciated.

Anthony

nchawkeye · Friday at 9:37 PM

The Mag Spark screws out and you screw in a new nipple, you will have to figure out what size threads are in the drum.

2 shots · Friday at 9:39 PM

is it the pic or are those holes mighty deep in the breech area??

snakebit · Friday at 9:48 PM

2 shots said:
is it the pic or are those holes mighty deep in the breech area??

Yep. That's what I noticed too.

BoomStick · Friday at 9:52 PM

Soak it in a penetrating oil (kroil) for a day, grab the mag spark with a needle nose vice grip. You'll probably mess it up gripping it like that but if you're not keeping it...that's what I would try.

Can also try filing 2 flats on it and try a spanner, but could be kinda thin for much filing.

Or hack saw through the middle to create a slot and a big screwdriver.

2 shots · Friday at 9:55 PM

have you checked to see if it is loaded?? soak it and find an ez out that fits . try to use it in the larger part ,not the flash channel.

Daytime Smoker · Friday at 10:07 PM

2 shots said:
have you checked to see if it is loaded?? soak it and find an ez out that fits . try to use it in the larger part ,not the flash channel.

It’s not loaded. That’s the first thing I always check.

Daytime Smoker · Friday at 10:08 PM

BoomStick said:
Soak it in a penetrating oil (kroil) for a day, grab the mag spark with a needle nose vice grip. You'll probably mess it up gripping it like that but if you're not keeping it...that's what I would try.

Can also try filing 2 flats on it and try a spanner, but could be kinda thin for much filing.

Or hack saw through the middle to create a slot and a big screwdriver.

That’s definitely crossed my mind.

Daytime Smoker · Friday at 10:10 PM

2 shots said:
is it the pic or are those holes mighty deep in the breech area??

It’s the pic and angle. I vaguely remember using this when I was younger. Well, dad used it more than me. I think back in the day when Tennessee introduced a Blackpowder season. I do think Dad built this from a kit but had a smith drill and tap it for him. That’s been many years ago.

Mad Professor · Friday at 10:27 PM

Daytime Smoker said:
It’s the pic and angle. I vaguely remember using this when I was younger. Well, dad used it more than me. I think back in the day when Tennessee introduced a Blackpowder season. I do think Dad built this from a kit but had a smith drill and tap it for him. That’s been many years ago.

Those holes should get filled with the correct size screws.

I think the threads should be 6-1mm for the nipple.

https://www.trackofthewolf.com/List/Item.aspx/159/1

CScott · Friday at 10:59 PM

I bought a TC with a Mag Spark type primer adapter and found it was removable by a hex (Allen) wrench inserted down through the nipple.

ppg1949 · 2024-12-21T00:53:46-0500

For the holes, take one of the screws that you removed and go to your local hardware store. To my knowledge they all have a screw thread sizing template to find the right size thread you need. Most local hardware stores carry a selection of gunsmithing screws. I’m not sure about the big box stores. I had bought a barrel with the same problem. My local Ace Hardware store had what I needed. I bought several different lengths to make sure I got the correct one. If nothing else, by using the screw thread template you will at least know what size thread you will need.
Good luck.

aussie pete · 2024-12-21T02:05:17-0500

Daytime Smoker said:
So, I got this traditions deer hunter as a project from my father. Dad had an optic and had it drilled and tapped. No big deal. I took the scope and rings off. What I can’t figure out is how to change it back to a normal nipple. He had a mag spark and I’m not a fan of those anyway. Not that I have anything against them, just not my style. Anyway, how in the heck do I change it back? Here are a few pics after I got the mag spark nipple or topper off. Do I try to take the drum off? Like I said ya can’t beat basically free. And it’s a muzzy, so I’ll take those all day any day. Plus, I have a soft spot for something that came from my dad. Any help would be appreciated.

Anthony

I'd be doing what BoomStick advised - Dremel or cut a slot through the middle so you can use a screwdriver to get some leverage to turn it back out. I suspect you will be right with a replacement nipple, as those Mag Spark devices matched the same thread as the gun.

Pete

Sparkitoff · 2024-12-21T06:39:40-0500

CScott said:
it was removable by a hex (Allen) wrench inserted down through the nipple.

This is correct. There's a hex shape in there and the appropriate sized tool should take it right out.

Daytime Smoker · 2024-12-21T08:25:05-0500

Sparkitoff said:
This is correct. There's a hex shape in there and the appropriate sized tool should take it right out.

Hmm.. I’ll see what I can come up with. Thank you for that tip.

Anthony

Daytime Smoker · 2024-12-21T08:26:37-0500

ppg1949 said:
For the holes, take one of the screws that you removed and go to your local hardware store. To my knowledge they all have a screw thread sizing template to find the right size thread you need. Most local hardware stores carry a selection of gunsmithing screws. I’m not sure about the big box stores. I had bought a barrel with the same problem. My local Ace Hardware store had what I needed. I bought several different lengths to make sure I got the correct one. If nothing else, by using the screw thread template you will at least know what size thread you will need.
Good luck.

Thank you! I hav an ace out in town. I remember working at one when I was a young pup, that they always had very unique screws and threads with different pitches.

Anthony

Ed C. · 2024-12-21T09:56:28-0500

Vise grips if you have enough room to get them on there and brake it loose, then turn it out with pliers.

kelljp · 2024-12-21T10:05:39-0500

I have removed several of these by unscrewing them with an Allen wrench as was stated above.

Eric Krewson · 2024-12-21T10:13:42-0500

Those deep scope mounting holes scare, I would put in the screws to fill them in with red Loctite.

longcruise · 2024-12-21T12:14:52-0500

Yes, I did that with some over length screws on several TC barrels. Then cut them off and file to match.

I’m at a loss

Help Support Muzzleloading Forum:

40 Cal

Attachments

58 Cal.

69 Cal.

58 Cal.

Groovy...

69 Cal.

40 Cal

40 Cal

40 Cal

50 Cal.

32 Cal

54 Cal.

40 Cal

40 Cal.

40 Cal

40 Cal

54 Cal.

69 Cal.

54 Cal.

70 Cal.

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!