Disassemble the lock to finish it??

KH · Feb 3, 2025

Hello all,
Just finished my workbench to have a place to build.
I am about to start my first build, a Kibler Woodsrunner in 50 cal.
Thinking ahead to the metal parts, does the lock need to be taken apart to finish it? I am going to use JAX black and rub it back a bit.
Wondering if I need a spring vise coming my way.
Thanks for the input.

PEARL DRUMS · Feb 3, 2025

Yes it does.

Phil Coffins · Feb 3, 2025

Absolutely yes.

Flintlock Fellow · Feb 3, 2025

Congrats on the new workbench and jumping into your first build—the Kibler Woodsrunner is an excellent choice!

To get the best results when finishing the metal parts, I too would recommend fully disassembling the lock. You could just remove the cock and frizzen to access most of the lock face, but at that point, it’s only a few extra minutes to break it down completely. Taking the time to properly prep each part will definitely show in the final finish. There’s a direct correlation between the effort you put into prep work and the quality of the end result.

rafterob · Feb 3, 2025

Yes to both of your questions.

Buff1958 · Feb 3, 2025

Key you eye on the fly when you take it apart.... I lost my first one as I didn't know it was in there

The Crisco Kid · Feb 3, 2025

Clean off your new work bench and sweep the floor before you disassemble the lock. The little part you drop will be easier to find. I know about this.

Hatchet-Jack · Feb 3, 2025

Yes and yes. Store your parts in a little can or jar while you work on it so you don't loose them. Put the fly in a small Ziploc and put it in the can. Keep track of which screw is which so you don't mix them up.

tenngun · Feb 3, 2025

The Crisco Kid said:
Clean off your new work bench and sweep the floor before you disassemble the lock. The little part you drop will be easier to find. I know about this.

And lay newspaper or brown wrapping paper. There is the detent, often called fly, so named because it flys away
I like to put scotch tape on it and stick it in an envolope

The Crisco Kid · Feb 3, 2025

I put the fly and the small screws on a piece of masking tape, fold it over and label it. There are several ways of keeping things organized, the memory being the one that seldom works.

tenngun · Feb 3, 2025

The Crisco Kid said:
I put the fly and the small screws on a piece of masking tape, fold it over and label it. There are several ways of keeping things organized, the memory being the one that seldom works.

Take care too with the screws. Sear and bridal screws can all be a little different

Freedom · Feb 3, 2025

I have one of those super magnets in the bottom of a small tin cup. It grabs ahold of all the small parts and holds them fast.

KH · Feb 3, 2025

Great thoughts everyone, and notes taken.
I’m not sure if there is an exploded view of lock parts somewhere, but that would sure be nice. I like to know what is there before a part goes airborne on me. I’ve always been a “some assembly required” sort of nerd, so this will help me fully understand how it works as well.
Thank you gents.

Freedom · Feb 3, 2025

Kibler has a great video on disassembly/assembly of his lock on ytube

ChuckJonesWagon · Feb 3, 2025

Use your phone camera and take pics of the lock before you start. Then take a few more as you go along. Use color markers on the screw heads, take a pic, keep on going.

(Use different color markers for each screw)

Texcl2 · Feb 3, 2025

I agree with taking a picture before you take anything apart, it will save you a lot of headaches. Don’t be intimidated by disassembly, it’s not hard and you need to learn how to do it. Also filing and sanding the casting marks ofc your parts adds a lot to your finished product. I spend more time finishing my locks than any of the other parts including the stock. You will need a main spring vise and I recommend Kiblers brass punch to knock the hammer off the sear. As stated kibler has a couple videos on lock assembly and disassembly.

mikesto44 · Feb 4, 2025

One thing I do is I bought a magnet tray. I place it on my work bench. When I'm working on my locks. Follow the advice given here an you'll be all set. The Woodsrunner is a great, easy to do kit.. Enjoy

Texcl2 · Feb 4, 2025

Plus one on the tray. I have one on my bench at all times. I think it was free with a coupon from harbor freight, they are cheap there regardless.

mikesto44 · Feb 4, 2025

Texcl2 yes an they come in all sizes..

Rebel bull · Feb 4, 2025

mikesto44 said:
Texcl2 yes an they come in all sizes..

I used a magnetic sheet in my gun cradle to catch smalls

Disassemble the lock to finish it??

Help Support Muzzleloading Forum:

32 Cal

40 Cal

70 Cal.

40 Cal

62 Cal.

40 Cal

69 Cal.

54 Cal.

Cannon

69 Cal.

Cannon

Pilgrim

32 Cal

Pilgrim

62 Cal.

40 Cal

54 Cal.

40 Cal

54 Cal.

45 Cal.

Similar threads