1851 Navy .36 - Load Data???

[smoothshooter]

Just picked me up my first pistol (.36 cal.)& wondered why I found two really different loads.? :: One says 9-12 & other 22 gr. of triple F. 9 is a long way from 22!!!

I'd sure appreciate any tips on loading too. What do you use to over fill the powder before wad. What's best to use to seal everything? Crisco?

Thanks

First off, grease over the chambers doesn’t have any effect on chain-fires, contrary to what a lot of people will tell you. Loose caps, or WAAAYYY undersized balls CAN cause that. If you ever have a chain-fire, it is unnerving, but will not damage you or the gun. Identify the problem, fix it on the spot if you can, reload, suck it up and go on.
In the old days almost no one ever used greased wads and they for darned sure didn’t put grease over the chamber mouths. They loaded and shot everything dry.
Also keep in mind you are not having to choose your powder charges as carefully as if you were loading smokeless in metallic cartridges. A lot of new black powder shooters have a lot of trouble getting out of that mentality, especially if they have some metallic cartridge loading experience.
The bottom line is that unless you are engaged in some serious competition, powder charges really don’t matter much as long as they are fairly consistent in weight. Load by volume. As long as the powder charge leaves enough room to seat the ball, you are good.
I am a believer in using thin lubricated felt wads that you should be making yourself (because of the ridiculous prices that retail sellers get). Seat these on top of each powder charge under the ball. They are for keeping the fouling in the barrel down somewhat ONLY.
Don’t make shooting these things more complicated than it needs to be.
I have been carrying and shooting them for years while working in the woods cutting down trees for firewood, clearing brush, splitting wood, fixing fences, target practice, etc., off and on for years. Some of the places I was doing work had a lot of copperheads in warmer weather, and I always shoot them on sight.
I have gotten older, and don’t get the opportunities to shoot quite as much as I used to, but I’m still doing it occasionally.
The two revolvers I have always used the most have been tweaked a little by me, and are monotonously reliable.

 

[smoothshooter]

Really ? why is that? The cylinders are lubed up on the end after loading. The caps have nothing to do with chain firing. This is not my first BP revolver friend.

Disagree. Chain-fires come from the rear.
The CYLINDER is that big round thing that has all the holes in it.
The CHAMBERS are the holes where the powder and bullets go.

 

[smoothshooter]

Interesting comments! Very good post.

I am not convinced that Colts were meant to be zeroed at 75 yards. I think it just worked out that way because the manufacturer wanted to use a low-profile front sight that did not snag on anything as it was being pulled out of a holster or belt.
At very close range, where most handgun use takes place, zero does not matter. But I can tell you that very, very few people have ever been hit by the person aiming at them with a handgun at 75 yards, then or now. When you add in the fact that people generally didn’t waste components or money on target practice like we do now, it makes it even less likely that any handgun in those days was designed for 50 to 75 yard use.

 

[smoothshooter]

JEEVES,,, When you go to cleaning that revolver and if you take out the nipples, "as with all percussion revolvers", make sure you put the same nipple back in the chamber from which it came... Usually I do not remove the nipples but once a year for a complete thorough cleaning... The reason for this nipple placement is nipples will conform with the hammer and you want the same striking point at all times... Just thought I'd throw this in so you were aware of it. Looks like the rest of the folks have your loading question covered pretty well.

Also put a little smear of Anti-Sieze on the threads of the nipples before hou screw them back in.
You will thank me later.