Bore anti-rust formula

[Elkeater]

Heaven forbid I'm seeing a consensus here. An innumerable quantity of substances to prevent moisture from getting to our bores.

But most of us use moisture to clean the bore. So the most critical step in the cleaning procedure is to remove the cleaning moisture before we seal it in. I used to think WD-40 was good at that but I was wrong. Now I'm going with denatured alcohol or Heet. :yakyak:

 

[longcruise]

Denatured alcohol and even 91% isopropyl works fine for me.

 

[Loyalist Dave]

Well methanol does that and HEET is sold to absorb water in the fuel line and gas tank, so that would make sense. I think any alcohol would do that and speed the evaporation process.

LD

 

[coloradoclyde]

HEET in the yellow bottle is denatured ethanol.

Ethanol has a very high affinity for water.

Other alcohols like 70% or 90% isopropyl or rubbing alcohol already have water added to them, so their affinity or capacity to remove water is greatly reduced..

 

[Rifleman1776]

Heaven forbid I'm seeing a consensus here. An innumerable quantity of substances to prevent moisture from getting to our bores.

But most of us use moisture to clean the bore. So the most critical step in the cleaning procedure is to remove the cleaning moisture before we seal it in. I used to think WD-40 was good at that but I was wrong. Now I'm going with denatured alcohol or Heet. :yakyak:

It is still good at that task.
Dry patches and maybe some carburetor cleaner squirted through the nipple or touchhole to boot. Then use the lube/protectant you have faith in at the moment.

 

[Elkeater]

I think any alcohol would do that and speed the evaporation process.

LD

In a pinch, Bourbon?

 

[Billnpatti]

Heaven forbid I'm seeing a consensus here. An innumerable quantity of substances to prevent moisture from getting to our bores.

But most of us use moisture to clean the bore. So the most critical step in the cleaning procedure is to remove the cleaning moisture before we seal it in. I used to think WD-40 was good at that but I was wrong. Now I'm going with denatured alcohol or Heet. :yakyak:

As you know, it is imperative to remove all traces of water from the parts of the gun after a cleaning. You need to use whatever you find that works for you. There is always more than one way to skin a cat. Once the moisture has been removed the focus changes to how to keep the gun from rusting. I have found that for a relatively short term storage, just a good gun or machine oil works very well. Some folks have reported very good results from a synthetic motor oil. For longer-term storage, I like to use a product such as Barricade. There are also other good products for this application. The secret is to use a product that provides an occlusive seal against moisture and oxygen and contains a corrosion inhibitor. That's my take, anyway. :thumbsup:

 

[coloradoclyde]

I think any alcohol would do that and speed the evaporation process.

LD

In a pinch, Bourbon?

80 proof bourbon would 60% water.....Not real effective at removing water...

 

[mamero]

Denatured alcohol gets the nod. Its $12 a gallon at the local paint store. I then wile it down with balistol and this combination works for me.

 

[Loyalist Dave]

It is?

The MSDS online says it is

**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

Chemical Name CAS MIN MAX
Methanol 67-56-1 99 99
Proprietary Additive (none) 1 1


I don't think it matters though, eh?

:idunno:

LD

 

[Loyalist Dave]

80 proof bourbon would 60% water.....Not real effective at removing water...

....correct....and a waste of good liquor...

but 190 proof Everclear would work, but again, very expensive....

LD

 

[Elkeater]

I apologize, my dry attempt at borebon humor didn't take.

 

[coloradoclyde]

It is?

The MSDS online says it is

**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

Chemical Name CAS MIN MAX
Methanol 67-56-1 99 99
Proprietary Additive (none) 1 1


I don't think it matters though, eh?

:idunno:

LD

Dang!....You're right Dave....I think they changed it on me at some point.... :hmm:
It still works good.
Damn drunks were probably drinking it.

I've been using it cause I can buy it for less than $3.50 a gallon.

Thanks for correcting me.... :thumbsup:

 

[Rifleman1776]

Well methanol does that and HEET is sold to absorb water in the fuel line and gas tank, so that would make sense. I think any alcohol would do that and speed the evaporation process.

LD

Heet absorbs the moisture and holds it in a sorta glob in the fuel tank.
I have never been an advocate of alcohol for use in any ml application (until campfire time). What is suggested to remove moisture seems counter productive to me. The alcohol might absorb the moisture in a bore, but when allowed to evaporate wouldn't the moisture still be left behind? :hmm: That's my reckoning. Serious scientists might have a different slant on that.

 

[Zonie]

I tend to agree with you about the alcohol evaporating before any water that might be in it evaporates.

If anything, the increased cooling caused by the alcohol evaporating will reduce the tendency of the water to evaporate. Colder water evaporates more slowly than warm water.

That said, there is something the alcohol probably does to help dry things out.

If the water is in small nooks and crannies like the rifling grooves and the joint between the breech plug and the barrel form, the alcohol will absorb the water from these areas and distribute it throughout itself.

This will distribute the water in a thin, even layer. After the alcohol has evaporated, the now evenly distributed thin layer of water will easily evaporate quickly.

 

[coloradoclyde]

The alcohol might absorb the moisture in a bore, but when allowed to evaporate wouldn't the moisture still be left behind?

Only if the ratio nears or exceeds 1:1

 

[coloradoclyde]

I tend to agree with you about the alcohol evaporating before any water that might be in it evaporates.

Simple solutions for simple problems.

Squirt the alcohol down the barrel. Then swab.

No book reading , smoking, or phone calls in between steps......They should be seamless.

 

[Elkeater]

That said, there is something the alcohol probably does to help dry things out.

Yes, alcohol bonds with water and I wipe it out. Done.