I bought a T C with a broken ram rod all way to the breech, I have in the past made a grease fitting adapter and pushed out stuck balls with a grease gun, I am thinking about putting a small charge of 4f where the nipple goes and fire it, any of you ever did this?
Broken ram rod
- Thread starter old iron
- Start date
Help Support Muzzleloading Forum:
There's more than a few of us who have fired an entire ramrod, so it could work for a broken ramrod. How long has the broken ramrod been in that rifle? Did the ramrod break during cleaning or is there a load under the ramrod? The CO2 option or the grease gun has to be my choice if you don't know what is specifically at the breech.
Ramrods don’t just end up ‘broken all the way to the breech’, whatever that means. What does the individual that sold you the gun in this condition have to say about the issue?
Any idea of what may be under the broken ram rod? A blackpowder load? A smokeless load? Think before you just add some 4F and fire it, hoping for the best.
I would feel best using compressed air or grease, but maybe I’m just too careful with guns I own. That said, have at it with the 4F and report back. You have eight fingers, two thumbs and two eyes. What could possibly go wrong that you couldn’t recover from?
Last edited:
Gtrubicon
50 Cal.
- Joined
- Jun 19, 2021
- Messages
- 1,405
- Reaction score
- 2,450
I’d be very cautious, only from the standpoint of is there a load in it and what is the load. Many don’t take these guns seriously. A potential load of smokeless is something I wouldn’t risk shooting off. Broken ramrod yeah, no worries as long as I knew 100% that’s all that was in the bore. My buddy thought red dot would work in his friends 1851 navy since they didn’t have any BP. It worked so well that it blew the cylinder apart upon firing, blew the grips apart, never found the hammer. Luckily this idiot was ok after lots of stitches.
First off I have enough common sense not to hold the gun while firing, second I have taken a rod and measured where it is broken and there's no way a load is there because of the measurement, third how could it get stuck pushing a ball down, fourth I used a bore scope to confirm it is a broken ram rod, already tried air , the pawn shop I bought it from has no history on it.
- Joined
- Mar 1, 2022
- Messages
- 1,232
- Reaction score
- 1,543
The 4Fg dribble should work just fine. Make sure your replacement ram rod tip is pinned in place.
Well the reason I was asking is I am not sure I can get enough powder in the nipple hole to fire it out , but as soon as I get aa nipple from TOW we go a find out 
Well the reason I was asking is I am not sure I can get enough powder in the nipple hole to fire it out , but as soon as I get aa nipple from TOW we go a find out
Well the reason I was asking is I am not sure I can get enough powder in the nipple hole to fire it out , but as soon as I get aa nipple from TOW we go a find out
Well the reason I was asking is I am not sure I can get enough powder in the nipple hole to fire it out , but as soon as I get aa nipple from TOW we go a find out
Well the reason I was asking is I am not sure I can get enough powder in the nipple hole to fire it out , but as soon as I get aa nipple from TOW we go a find out
Not sure why it posted so many times
Thanks Rifleman
Well, go edit and delete those posts. You can do that.
How?
- Joined
- Sep 10, 2021
- Messages
- 190
- Reaction score
- 184
I’ve trickled a small enough amount of 4F under the nipple that could push a dry ball out about 10-15 ft. Pretty impressive that a little amount can have that sort of result.
Thanks Blackeagle good to hear it worked for you, have a nipple on the way , hope it works for mine, if not I'm going to make a drill with collars so it doesn't hit the barrel, to keep it in center , know it will be a lot of work , but don't want to damage barrel
For a couple of days after your post, there’s 3 little dots down and to the left after your post. In there it says “edit post” or something like that.
Thank you! Looked back to try but I guess it’s been too long
