Finally did it.
- Thread starter snakebit
- Start date
Help Support Muzzleloading Forum:
Powder Patch Ball Flint.
Check
hanshi
Cannon
And be patient as you get to know it.
Look up Bob's Black Powder Notebook, wealth of info on the flinter
Thanks
Phil Coffins
69 Cal.
Black powder, substitutes don’t work well.
I use black. I only use Pyrodex-P in my Crockett.
westrayer
40 Cal
80 grain of FFFg should be a good load for you. That barrel will burn up even heavier charges. Try to find both .490 and .495 round balls and then .015 and .020 thick patches. It is a pain to find the correct combination but often it will yield surprisng results of from bad to good.
My first flintlock was a GPR .54 cal , here’s what I remember from that experience..
First … Mine didn’t shoot reliably, so I drilled the touch hole out… problem solved.
Second … Look at your shot patches..the crown / rifling on mine cut the patches for the first few shots. However it was new at the time.. hopefully yours will be broke in.
Third… I never cared for the buckhorn sights.
Forth … mine liked heavier charges… 100 grn fffg with a .530 ball & .018 patch.
Fifth … I never liked the hooked butt plate…
Even shooting the gun off the bicep, that point on the toe just ate me up!
Other than that it was a great rifle that shot well..
Good Luck with yours & Welcome too the dark side..
First … Mine didn’t shoot reliably, so I drilled the touch hole out… problem solved.
Second … Look at your shot patches..the crown / rifling on mine cut the patches for the first few shots. However it was new at the time.. hopefully yours will be broke in.
Third… I never cared for the buckhorn sights.
Forth … mine liked heavier charges… 100 grn fffg with a .530 ball & .018 patch.
Fifth … I never liked the hooked butt plate…
Even shooting the gun off the bicep, that point on the toe just ate me up!
Other than that it was a great rifle that shot well..
Good Luck with yours & Welcome too the dark side..
For mine, I use a .490 ball, .015 patch, and 50 grains of FF powder. That combination has won many matches for me.
Just done did the same thing. My advice is to go shooting with an old guy that’s been doing it for years, pay attention, and do what he does. In a short time you will have your own routine including the tools and things that work for you. Oh, never, never dwell on the cost of accessories………just push the send button 
Pete G
76 Cal.
That’s how I ended up with a tiny engraving hammer that cost $45.00 (plus shipping)Just done did the same thing. My advice is to go shooting with an old guy that’s been doing it for years, pay attention, and do what he does. In a short time you will have your own routine including the tools and things that work for you. Oh, never, never dwell on the cost of accessories………just push the send button
laagamer
36 Cl.
- Joined
- Sep 15, 2021
- Messages
- 83
- Reaction score
- 109
The end with the hole goes boom!
No, but I love mine! Recommend sighting yours in. I bought mine used and it wasn't the greatest. Had to file down the front sites a bit, and tap the rear sight over a bit after some tests at 50yd sitting.
No, but I love mine! Recommend sighting yours in. I bought mine used and it wasn't the greatest. Had to file down the front sites a bit, and tap the rear sight over a bit after some tests at 50yd sitting.
muskethunter1109
J. McKane
Everyone has different preferences when it comes to how much powder you use compared to what’s recommended. Start out light taking a few shots with each powder load. Then work your way up until you get to a powder load you’re happy with and is accurate. You’ll be having tight groupings at 100 yards without a sore shoulder the next day in no time!
