Investarms Hawken hammer position

[alde]

I have an Investarms .50 cal Hawkin I purchased used at the local gunshop. It's in great condition and shoots very well. The issue I have is that when the hammer is at half **** it's too close to the nipple to place a cap on. Is it possible that someone removed the hammer and replaced it out of position? I really don't feel comfortable pulling the hammer to the full **** position to cap it. Thank you for any suggestions.

 

[Ed C.]

That is pretty common. Both my Investarms .50 cal. Hawkins are that way. I just go ahead and cap at full ****. Just pay attention to the direction of the pointy end when doing so.

 

[alde]

That is petty common. Both my Investarms .50 cal. Hawkins are that way. I just go ahead and cap at full ****. Just pay attention to the direction of the pointy end when doing so.

Thanks Ed. I try to be extra careful with this one.

 

[Bad Karma]

I have an Investarms .50 cal Hawkin I purchased used at the local gunshop. It's in great condition and shoots very well. The issue I have is that when the hammer is at half **** it's too close to the nipple to place a cap on. Is it possible that someone removed the hammer and replaced it out of position? I really don't feel comfortable pulling the hammer to the full **** position to cap it. Thank you for any suggestions.

Very few TC rifles will allow you to cap your cone at half **** and your investarms is virtually a copy of the TC so I’d say it’s functioning as designed.

 

[user 60625]

I'm glad you brought this up as I have a TC Hawken .50 and one of the first thing, I noticed was how close the hammer was to the Nipple at half ****. The second thing was the height of the nipple, and I replaced it today with a standard Thompson version. Problem solved....

 

[NorthFork]

@alde

I think you have the wrong nipple installed. Investarms over the years changed overall nipple length. I found this out on my 3 Investarm/Lyman's. I used this nipple- (I primarily use Treso nipples). You need the new style. #11-50-66

 

[NorthFork]

I'll also add that if you insist on a stainless nipple, TOTW part#RLGP-S is the proper stainless nipple for your gun.

 

[alde]

@alde

I think you have the wrong nipple installed. Investarms over the years changed overall nipple length. I found this out on my 3 Investarm/Lyman's. I used this nipple- (I primarily use Treso nipples). You need the new style. #11-50-66


View attachment 237382

Thank you very much for this information. I'll order a couple of the correct nipples.

 

[NorthFork]

Thank you very much for this information. I'll order a couple of the correct nipples.

If you buy from The Possibles Shop (a very reputable seller!) be careful when ordering! There is a typo in the verbiage. The Treso number is correct though. Order with confidence using #11-50-66 even though it "says" it is for the 'other' nipple. He is about the only seller of Treso right now. It's him or Track of the Wolf for stainless using the part# I gave in my other post. This should fix your problems. It did for me!

 

[alde]

If you buy from The Possibles Shop (a very reputable seller!) be careful when ordering! There is a typo in the verbiage. The Treso number is correct though. Order with confidence using #11-50-66 even though it "says" it is for the 'other' nipple. He is about the only seller of Treso right now. It's him or Track of the Wolf for stainless using the part# I gave in my other post. This should fix your problems. It did for me!

Thanks again. I already ordered a couple from TOTW based on your post. I had a couple of other thing in my basket anyway so just added the nipples and ordered.

 

[UNCLERICKY]

One last thing, make sure you get the correct thread pitch. Investarms has the fine pitch the 6 x 1. Ask me how I found out ;-) .
Rick