-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
Making Paper Cartridges
- Thread starter starman
- Start date
Help Support Muzzleloading Forum:
Cigarette papers.
Yes those work for revolvers, quite well, but are not big enough nor solid enough for smoothbore cartridges.
So you go to the Dollar Store/Dollar General, OR you go to library if it sells off books from time to time...,
And you find a book for sale for a dollar, with pages large enough to cut for at least one cartridge per leaf, but some books you can get two made from each leaf of paper in the book. Tear out the paper, cut, and roll. Book paper is a a bit better than newsprint, though I've not had trouble with newsprint..., I just don't like buying papers written by folks who write fiction for the masses, and call it "truth"...ooops don't want to hijack a thread....
So get a book or two. Avoid very glossy paper too.
LD
Oops, missed brown bess. Thanks for the rescue.Yes those work for revolvers, quite well, but are not big enough nor solid enough for smoothbore cartridges.
So you go to the Dollar Store/Dollar General, OR you go to library if it sells off books from time to time...,
And you find a book for sale for a dollar, with pages large enough to cut for at least one cartridge per leaf, but some books you can get two made from each leaf of paper in the book. Tear out the paper, cut, and roll. Book paper is a a bit better than newsprint, though I've not had trouble with newsprint..., I just don't like buying papers written by folks who write fiction for the masses, and call it "truth"...ooops don't want to hijack a thread....
So get a book or two. Avoid very glossy paper too.
LD
I have used graphite tracing paper from Hobby Lobby. Little pricey but works fine, leaves very little junk in the chambers. If you use too much glue on the spark end, it will leave a ring of paper. I have reloaded that way ( nothing gets by me), and had no problem. It doesn’t seem to smolder like some,
Brokennock
Cannon
Apparently that we are talking about a Brown Bess, in the Smoothbore section, got by you....
Twice, lol.
Had revolvers on the brain and there isn’t much parking space there.....sorry
Brokennock
Cannon
No apology needed. I found it funny,,,,,, hope you do too.
- Joined
- Mar 20, 2020
- Messages
- 93
- Reaction score
- 54
I always used the precut paper from smiling fox, a bit pricey but is tough enough for the job, lubed the ball end and they were deadly
- Joined
- Aug 15, 2010
- Messages
- 5,346
- Reaction score
- 5,100
If you dare to go out in public, any garage sale will have romance novels for next to nothing. A dollar will keep you shooting for a while.
There are a lot of good suggestions here, and plenty of things to try. Lots of ways to skin this particular cat! You'll want to find what works best for you.
Here is what has worked best for me:
If you can go to an art supplies store, ask for a pad of artist's newsprint. It's like the paper newspapers are printed on, but a little thicker, and, of course, there is no printing on it. I've made paper cartridges out of it for my fowler and for my muskets, and it works well. It is stronger than newspaper, but easier to tear off than typing or printer paper. I've never tried pages from a book.
Bear in mind also that paper has a "grain." Almost any paper, including artist's newsprint, will tear in a nearly straight line in one direction, but it tears at an angle and you end up ripping off little bits and pieces if you tear it the other way. If you're making paper cartridges, you probably have a trapezoid-shaped pattern that you use for making the cartridge papers. Experiment with it a little, and figure out which way to orient your pattern so you'll end up tearing straight across the cartridge when you bite off the tail. You may waste a little paper, but the results may be worth it. This will make the cartridges easier to bite off, easier to manipulate once opened, and less likely to spill powder if it doesn't rip down the side.
Best regards,
Notchy Bob
Here is what has worked best for me:
If you can go to an art supplies store, ask for a pad of artist's newsprint. It's like the paper newspapers are printed on, but a little thicker, and, of course, there is no printing on it. I've made paper cartridges out of it for my fowler and for my muskets, and it works well. It is stronger than newspaper, but easier to tear off than typing or printer paper. I've never tried pages from a book.
Bear in mind also that paper has a "grain." Almost any paper, including artist's newsprint, will tear in a nearly straight line in one direction, but it tears at an angle and you end up ripping off little bits and pieces if you tear it the other way. If you're making paper cartridges, you probably have a trapezoid-shaped pattern that you use for making the cartridge papers. Experiment with it a little, and figure out which way to orient your pattern so you'll end up tearing straight across the cartridge when you bite off the tail. You may waste a little paper, but the results may be worth it. This will make the cartridges easier to bite off, easier to manipulate once opened, and less likely to spill powder if it doesn't rip down the side.
Best regards,
Notchy Bob
RAEDWALD
40 Cal.
I too use book pages but I use cheap pre 1850 (usually turgid religious works) as they are rag paper (pre wood pulp paper) and the sizing has perished so are soft and choke without tearing or crinkling.
Greenjoytj
54 Cal.
Are you supposed to nitrate the paper so as to create a type of flash paper in order to help the paper to be throughly consumed upon firing.
RAEDWALD
40 Cal.
No. The ball is inside the paper and the whole thing is run down the bore once the powder s emptied into the barrel. Two sharp raps of the rod will form the paper into a crude sabot/wad and the whole thing will be expelled when it is fired. The ball flies free of the paper even though the paper is choked over the ball.
- Joined
- Apr 27, 2005
- Messages
- 119
- Reaction score
- 231
I have tried many different papers, but based on someone else's recommendation, I bought some brown masking paper at Home Depot and it is the absolute best I have used for making musket cartridges or for Civil War miniball cartridges.
https://www.homedepot.com/p/TRIMACO...General-Purpose-Masking-Paper-12906/202040753
Clueless on the Delaware
32 Cal
Have you tried EZ Widers?
- Joined
- Apr 27, 2005
- Messages
- 119
- Reaction score
- 231
A miniball cartridge made from the brown masking paper.
Banjobison
32 Cal
coffee filters seem to work well (and are pretty economical) I mix water and potassium nitrate and dunk the coffee filters in it, let it dry in the sun.
Canute Rex
40 Cal.
- Joined
- Apr 19, 2012
- Messages
- 397
- Reaction score
- 303
I have always just nabbed a few sheets of 8 1/2 x 11" out of the computer printer. Fold in half lengthwise; cut along crease. Take each stack of long strips and fold at a 45 angle in the middle to make an equal-leg L. Cut along the angled crease and you have four cartridges per sheet with a nice angled tail for rolling.
Yeah they are just not going to hold 100 grains of powder for blanks in a cartridge box and sustain being yanked when it come time to load.
LD
