Questions for TVM Owners

[Rod Man]

How often do you pull the vent liner for cleaning? How often Do you replace? Is this a proprietary item? It looks like it’s hand fitted. No problems here but I can see where the slot is relatively shallow not sure if removing it every time for cleaning is a good idea. I have one of @davec2 ‘s cleaning implement's that really makes me wonder if I need to pull it anyway.

Thoughts?

Thanks in advance for replies!

RM

 

[smoothshooter]

How often do you pull the vent liner for cleaning? How often Do you replace? Is this a proprietary item? It looks like it’s hand fitted. No problems here but I can see where the slot is relatively shallow not sure if removing it every time for cleaning is a good idea. I have one of @davec2 ‘s cleaning implement's that really makes me wonder if I need to pull it anyway.

Thoughts?

Thanks in advance for replies!

RM

NEVER!
Ideally, someone put a little anti-sieze on the threads before installing it, though.

 

[Rod Man]

Thanks,

Yeah it’s pretty apparent that it’s not necessary. But I do OCD about the cleanliness of my shoot’n Irons.

 

[smoothshooter]

Thanks,

Yeah it’s pretty apparent that it’s not necessary. But I do OCD about the cleanliness of my shoot’n Irons.

Even it a little crusty fouling stays in the liner, as long as you still have an open flash channel, no harm will be done because those liners are made of highly corrosion-resistant materials.

 

[Rod Man]

Roger that.

 

[Rod Man]

So, have any of you fellas ever shot one out and had to replace?

 

[smo]

Not me..

 

[Art Caputo]

I have owned three TVM’s over a 10-20 year period and have never removed them. No issues.

 

[Rod Man]

This is what I needed to here.

Thanks guys!

 

[Rod Man]

So the general consensus is “leave her be” and just shoot it!

I can do that!

 

[hanshi]

I only remove the liner before shooting and open the cone just a bit more. The liner gets a bit of "antiseize" on the threads before reinstallation. Other than that I only remove a liner if it's necessary when doing work on the barrel. After that I just leave them in and never have yet had to replace one.

 

[Rod Man]

Thanks for the info Sir.

RM

 

[Rock Home Isle]

I’ve got several TVM firearms, I’ve been shooting flintlocks for almost 3 decades, it never crossed my mind to ever remove a vent liner, unless I was replacing or repairing.

 

[ohio ramrod]

I recommend you pull and replace the vent liner when the hole "burns out " to larger than .070 inches. NOT BEFORE.

 

[Rod Man]

I recommend you pull and replace the vent liner when the hole "burns out " to larger than .070 inches. NOT BEFORE.

Where do you get the vent liners from TVM? Or is there another source?

 

[Grenadier1758]

The vent liners are likely to be either 1/4-28 or 5/16-24 and are available from most suppliers of muzzle loading building supplies. Since I don't recommend removing a vent liner unless you want to replace it, a call to TVM should get you the answer.

 

[springfield art]

How often do you pull the vent liner for cleaning? How often Do you replace? Is this a proprietary item? It looks like it’s hand fitted. No problems here but I can see where the slot is relatively shallow not sure if removing it every time for cleaning is a good idea. I have one of @davec2 ‘s cleaning implement's that really makes me wonder if I need to pull it anyway.

Thoughts?

Thanks in advance for replies!

RM

Not necessary to remove. Just keep all clean!

 

[andy52]

I've only removed one once, recently on the Traditions Pennsylvania where I had to lower the pan because it was covering the vent. Figured I'd go ahead and pull it to check the vent hole, it was fine so I just put it back in place.

 

[EC121]

I have seen one shot out. It usually happens when the hole is filed down to a knife edge during installation. A friend's rifle shot fine then the group opened up. He found the hole was oval shaped instead of round. He replaced the liner and the group came back.
It is best to have a small flat edge on the hole. Maybe 1/64" or 1/32" to put more metal where the heat is. 1 No need to remove the liner. None of mine have a screw slot anyway. I clean my liner holes with a small pipe cleaner or dental brush.

 

[Rod Man]

Thank you all for the comments and insight. Thinking I will leave her be, keep on shoot'n and jus keep an eye on it.

Thanks again!

RM