Refurbishing an old CVA Frontier. Used vinegar to remove the barrel bluing. Tried to refinish with BC Plum Brown barrel finish, but can't get an even finish. Thinking of starting over. Does anyone know if soaking the barrel in vinegar will remove the Plum Brown finish?
Removing Birchwood Casey Plum Brown barrel finish
- Thread starter JPW
- Start date
Help Support Muzzleloading Forum:
64Springer
75 Cal.
Apply some vinegar and see if it removes the plum brown finish.
Did you steel wool it down good and then use an excessive amount of degreaser?
Erwan
45 Cal.
For me too: white vinegar and a bit of steel wool 000 or 0000...
- Joined
- Mar 21, 2022
- Messages
- 1,558
- Reaction score
- 1,879
Polish it off with fine sand paper. Make sure you degrease the bare metal really well before putting on the first coat of browning solution. I clean the parts with acetone and rinse off a couple of times. Dry with a paper towel and then go over it with a heat gun. Make sure you don' touch the parts with your bare hands after degreasing. The oils from your skin will interfere with the solution. I wear nitrile gloves. I clamp a dowel in a vice and slid the barrel on to the dowel. I use Track of the Wolf browning solution. It does not go on even to start with. It starts to even out after a few coats if you do it right. Be very careful when carding the browning that you don't take too much off. I use a piece of denim or light canvas to lightly rub the last application back before applying the next coat..
Phil Coffins
69 Cal.
Same way works great with Plum Brown.
I'm rebuilding a rifle I built in 1976 and browned with Plum Brown. It came out uneven because I didn't know what I was doing but it has held up great all these years. I really bungled the stock architecture so I restocked in and will have to refinish the barrel as well. I'm still thinking about what brown I should use, Plum Brown or one of the slow formulas. I spend a lot of time thinking lately!
I'm thinking that this post doesn't answer the OP's question but I'll probably just sand the original finish off with 400 grit.
I'm thinking that this post doesn't answer the OP's question but I'll probably just sand the original finish off with 400 grit.
Sidney Smith
58 Cal.
- Joined
- Feb 17, 2019
- Messages
- 2,205
- Reaction score
- 2,312
People trash plum brown, bit I've had real good results with it. You have to follow directions though. I personally prefer the hot browning method like plum brown over the humidity activated stuff. I used Laurel Mountain Forge on one of my builds and I followed the directions to the letter and the finish looked horrendous. Never again.
longcruise
70 Cal.
Naval jelly?
Birchwood Casey blue and rust remover works good, Evaporust does too
I’ve found using Plum Brown, I heat in oven and metal to 320, (metal is supposed to be 275, but cools as it’s handled) apply plum brown liberally, repeat process. Once second coat is on and metal cools, I rinse it in ammonia to stop the blossoming action, then coat metal with gun oil. Until the final step, the browning does appear complete.
- Joined
- Nov 1, 2018
- Messages
- 3,885
- Reaction score
- 2,914
Steel wool magic erasers and windex or just water work well
stephenprops1
45 Cal.
What he said ^^.
Sand paper and a block, it's too easy. It ain't rocket science.
Naval jelly first if you want a jump start,, but then follow the instructions,, and prep the surface with fine sanding.
It's easily done with 15 minutes time, honest. If you wanna complicate it you could do it for full hour.
p.s. look for naval jelly by the painting stuff at the local hardware store. it's only a couple bucks. wear gloves.
This.
Brush on some naval jelly, let set about 10 minutes and then hit it with a green scratch pad. Just did a barrel a few month ago and messed up and had to start over.
kelvinator
32 Cal.
I recently browned the tang and but plate/toe plate of my Santa Fe hawken with the Laurel Mountain Forge stuff and I thought it turned out good.
My first attempt at browning anything really. Maybe it works better on some steel/iron than others?
Attachments
Felix the Cat
40 Cal
.. another vote for Laurel Mountain Forge! Can't get Plum Brown to work after many attempts.. too streaky and uneven.
I generally start with a coat of LMF and then almost remove it all with wet 0000 wire wool to flatten the surface. On subsequent coats scrub off with wet denim...
I generally start with a coat of LMF and then almost remove it all with wet 0000 wire wool to flatten the surface. On subsequent coats scrub off with wet denim...
