Uncle Miltie
50 Cal.
I use either 160 gr GOEX Cartridge or 220 gr Elephant ffg.
Slug Rifle Projectiles
- Thread starter Uncle Miltie
- Start date
Help Support Muzzleloading Forum:
Sun City
45 Cal.
I've been casting since 1948 and I can tell you that the man casting those slugs....knows what he's doing!!
Uncle Miltie
50 Cal.
I had excellent mentors!
Sun City
45 Cal.
I wish I owned a good slug gun!! Are you loading with a false muzzle??
52Bore
40 Cal.
- Joined
- Dec 14, 2016
- Messages
- 683
- Reaction score
- 989
How does the nipple hold up with that load?
Mfg?
Uncle Miltie
50 Cal.
The nipples do allright, maybe 200 shots. I have a few left made by the fellow who made the molds and tools but am running low.
I tried platinum lined nipples with the platinum threaded, pressed in and staked but they all failed: the platinum eventually disappeared. The ones that are most durable for me are made of heat treated stainless steel though I don't know what alloy.
I tried platinum lined nipples with the platinum threaded, pressed in and staked but they all failed: the platinum eventually disappeared. The ones that are most durable for me are made of heat treated stainless steel though I don't know what alloy.
Sandro_Ventania
40 Cal
Have you ever tested slightly lighter projectiles? maybe with 600 grains.
Uncle Miltie
50 Cal.
No, 977 grains 1 piece pure lead bullet is the lightest I use. I have molds and swage for a 2 piece bullet that weighs almost 1300 grains but it is more work to make and shoots no better.
Uncle Miltie
50 Cal.
Yes, here are a few photos of the loading muzzle.
Attachments
- Joined
- Jan 31, 2009
- Messages
- 13,221
- Reaction score
- 7,560
Thanks for info and pictures.
Sun City
45 Cal.
Here's a little tidbit of info that some folks don't know about. When these rifles were put together and machined by the Old Masters....so as to have the lands of the barrel match exactly the lands within the false muzzle.....the barrels were either made or ordered extra long and cut off at the length desired or either the false muzzle portion was machined separately and then prior to the barrel being rifled the false muzzle was clamped onto the barrel and then the entire apparatus was rifled! Perfection as near as possible was the desired result! And the bullets were two piece and swaged together with the rear portion being slightly softer than the front portion!
Uncle Miltie
50 Cal.
You are correct sir.
- Joined
- Jan 31, 2009
- Messages
- 13,221
- Reaction score
- 7,560
Uncle Miltie, what's your rifling geometry look like? Lands and grooves of equal width, or one smaller than the other? How many grooves for the length of bullet perimeter? Approximate depth of rifling? Sides of the grooves slanted a little? Rounded corners down in the grooves or sharp corners?
Uncle Miltie
50 Cal.
18 lands and grooves, approximately 0.0025" deep. Never measured the width of the lands and grooves but the grooves appear to be slightly wider. Rifling angles, sharp /round edges I have not measured.
The bore is choked, beginning about 4" down from the muzzle. The bullet is 1.575" in length and 0.552" in diameter at the base.
I use an oiled paper patch of about 0.0025" inches which likely bulks up to 0.003" after oiling.
The patched bullet rides on top of the lands while loading. Once the guide (piston) starter gets the bullet past the choke I can finish loading it with the pressure of one finger: it's that easy.
The bore is choked, beginning about 4" down from the muzzle. The bullet is 1.575" in length and 0.552" in diameter at the base.
I use an oiled paper patch of about 0.0025" inches which likely bulks up to 0.003" after oiling.
The patched bullet rides on top of the lands while loading. Once the guide (piston) starter gets the bullet past the choke I can finish loading it with the pressure of one finger: it's that easy.
Sun City
45 Cal.
Lordy...it would be a hoot to own that dude!
Sandro_Ventania
40 Cal
I've never seen something like this used.
Is the purpose accuracy or ease of loading?
Uncle Miltie
50 Cal.
It's a blast!
Uncle Miltie
50 Cal.
Accuracy. The bore must be cleaned after every shot. The weight of the rifle, loading muzzle, telescopic sight and shooting from a bench were done solely to win shooting matches.
dehart.stephen
36 Cl.
Many thanks for sharing your Slug Rilfe experience with us. There's way too little written about them, and the false muzzle photos are great. I like the milled slots.for paper-strip cross patch. Do you use any sort of lube wad or card wad between bullet and powder, or does the 'tween-shot cleaning make that moot?
Uncle Miltie
50 Cal.
Cleaning between shots makes fouling sort of a non issue I suppose. When I began shooting this rifle I used a lubricated felt wad between the bullet and powder to protect the base of the bullet from hot gases caused by the conflagration of all that powder. One day I left the wads at home, shot the rifle anyway and found accuracy to be better without the wads. I haven't used them since.
Similar threads
