Taylor firearms called me to tell me that they got a shipment of spiller &burr revolvers this morning. Don't know how many. Maybe others are getting them too.
Spiller & Burr
- Thread starter ormond tony
- Start date
Help Support Muzzleloading Forum:
user 52391
.45 Calibre
- Joined
- Jan 27, 2022
- Messages
- 314
- Reaction score
- 509
DGW has them in stock also.
CaptainKirk
54 Cal.
- Joined
- Feb 25, 2010
- Messages
- 2,245
- Reaction score
- 879
Are you looking for one? Be aware they are quite small compared to a brass NMA. I wanted one until my friend let me handle his. After getting my trigger finger unstuck I handed it back to him with a thanks and a note to self I no longer wanted one.
Tyler L
40 Cal
Yeah, they still show it in stock, but if I put it in the cart it says they will back-order it
Well, I couldn't resist and ordered one from Dixie. Really happy with the service, ordered Wednesday morning and I got it today. I don't know when I can get a chance to shoot it, but overall it seems really nice. Typical not so great Pietta grip fitting, but other than that I can see no flaws. It looks like they fixed a few of the complaints about the earlier revolvers. The hammer no longer interferes with seeing the rear sight, the nose of the hammer fits nicely into the safety notches, and it looks like they enlarged the loading cutout in the frame so there is now room for conical bullets. The rammer is still long though, sticking into the cutout, so that might still interfere. I can see the comment about it not being good for large hands though, pretty small in the grip area. Luckily fits me pretty well though. I expect it will shoot really high, but I don't mind making a taller front sight if needed.
Don't back-order. It may take ages and ages before they get more.
Tyler L
40 Cal
I know, I ordered one from Dixie; should get it Monday.
Let us know what you think of it!I know, I ordered one from Dixie; should get it Monday.
Tyler L
40 Cal
OK, I got my Spiller & Burr from Dixie today, and took it apart to clean. This is my first Pietta product so I was really curious how it would compare to a Uberti.
Overall, I am happy with it. I might strip the finish off the grips as the stain bled over the brass inserts which looks weird. It'll be a while before I can shoot it. Can't wait!
- Pietta's box with the styrofoam insert is waaaaay better than Uberti's flimsy boxes! And the manual actually has a parts diagram.
- The hammer does indeed fit into the safety notches. I forgot to check the sight clearance.
- It does look like the rammer is too long to load conicals. Unfortunately I don't have any here to try.
- Yes, the wood grips could be fit better.
- The worst defect is the edge of the left side recoil shield is rough. I will have to sand and polish it.
- The left rear edge of the grip is slightly rough.
- The bolt has a burr on one leg, although it doesn't touch anything and doesn't affect function.
Overall, I am happy with it. I might strip the finish off the grips as the stain bled over the brass inserts which looks weird. It'll be a while before I can shoot it. Can't wait!
Pics, please, after you get her cleaned up!!
The Spillers foul badly due to the frame flat in front of the chambers blowing debris directly into the cylinder pin.
Poor design, and the Pietta rendition is crudely built and looks nothing like the original if compared side by side.
Poor design, and the Pietta rendition is crudely built and looks nothing like the original if compared side by side.
user 52391
.45 Calibre
- Joined
- Jan 27, 2022
- Messages
- 314
- Reaction score
- 509
I just noticed, DGW has these available in kit form also...$20 less than the finished version, for all you cheapskates!
Tyler L
40 Cal
Wow !! Now I want one too
Tyler L
40 Cal
Question for anyone else that owns one of these:
Does the T-shaped pin that retains the cylinder pin rotate super easily?
I think it is supposed to have some friction, and should therefore be slightly shorter so the wave washer under the screw actually touches the frame.
Does the T-shaped pin that retains the cylinder pin rotate super easily?
I think it is supposed to have some friction, and should therefore be slightly shorter so the wave washer under the screw actually touches the frame.
Last edited:
Mine rotates very easily, the washer touches the frame, but just barely.
- Joined
- Apr 7, 2012
- Messages
- 741
- Reaction score
- 1,010
A medley of YT
Forgotten Weapons
Eras Gone
Blackie Tomas
11BangBang
Dualist1954
Forgotten Weapons
Eras Gone
Blackie Tomas
11BangBang
Dualist1954
