westrayer
40 Cal
I missed this one for sale on another site. Crazy expensive but much more compact than the Lyman 57 I have on my Deerstalker cap.
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
T/C #7194 tang mounted peep sight
- Thread starter westrayer
- Start date
Help Support Muzzleloading Forum:
- Joined
- Jan 31, 2009
- Messages
- 13,032
- Reaction score
- 7,291
The TC peeps come at a premium nowadays.
There were Renegade and New Englander models produced.
Luck of the draw, in an almost ghost town in Kansas that I once got sent to on assignment there was a store that had dusty packages sitting in the racks so I bought them.
There were Renegade and New Englander models produced.
Luck of the draw, in an almost ghost town in Kansas that I once got sent to on assignment there was a store that had dusty packages sitting in the racks so I bought them.
Last edited:
Give you $35 for it...
Sorry forgot to add the
The TC peeps are very compact and streamlined when compared to the Lyman 57. I have both mounted on different ML’s. IMO, the Lyman is the most bulkiest and worse peep ever sold. It is boxy, ugly and hangs out way too far off of the side of the rifle. So much so that I do not like laying my GPR on the left side during cleaning. The weight is all on that boxy Lyman peep. Therefore, I choose to lay it on the lock side instead.
I do not like a Lyman 57 peep but for now, I have not been able to find a better one to replace it. The only thing good about the Lyman 57 is they work, but at the expense of flat ruining the looks of a traditional ML, as well as the inconvenience.
The TC peeps are great. If you can find one, to install it you will have to drill and tap one hole in the tang. No buggy. The only down side is if you shoot heavy conical(s) it will have to be adjusted to where it sticks up quite high. Not that big of a deal once you carry the ML a while. Just have to keep in mind of perhaps brush or vines getting caught on it.
Last edited:
Can you put on a lower front sight?
Yes, probably could do that, depending on the specific application. Might not work out so well if one wanted to shoot RB as well.
On my New Englander, I’m running the stock front sight. So, a shorter one might cause one to take a pounding on the cheek bone. Recoil is fairly high with a 370 grain Maxi Ball buring 80 grains of 3F. Very accurate, however.
Last edited:
does anyone have a copy of the t/c instructions for those??
Ditt44
40 Cal
You will need this: Drill and tap set from Amazon
I bought this to drill and tap a tang. No big deal, just take your time. You will need a screw if your sight did not come with one or try to find a three-hole tang on ebay. I bought a 'spare' tang that was parted out from a Cherokee, which I hate to buy 'parts' but you can't always avoid it. I also picked up a couple 1-inch and 15/16-inch three-hole tangs a few years ago so that I had the option down the road to swap them if I got to that point with my vision.
My eyes just couldn't do the factory sights any longer so I put a #7194 model on a Cherokee. Had to add a taller fiber front sight... .490 maybe? Anyway, about 1/2 to 3/4 inch groups at 25 yards and often three touching holes. Finding a Seneca/Cherokee sight, which is smaller, is multitudes harder than finding a #7194.
I've bought five of the peeps over the years, two are laying around and I am contemplating buying a couple more Cherokee/Seneca tangs to swap out on my .36 and .45 Senecas. There is a guy on ebay that has a number of in-the-white tangs for those models. He might have spares for the Renegades and Hawken as well.
If you are going to drill/tap a tang, I would suggest buying a spare and mounting on that one, save your original just in case something goes wrong. I pulled it off... once... so either I got lucky or it isn't that hard to do.
I bought this to drill and tap a tang. No big deal, just take your time. You will need a screw if your sight did not come with one or try to find a three-hole tang on ebay. I bought a 'spare' tang that was parted out from a Cherokee, which I hate to buy 'parts' but you can't always avoid it. I also picked up a couple 1-inch and 15/16-inch three-hole tangs a few years ago so that I had the option down the road to swap them if I got to that point with my vision.
My eyes just couldn't do the factory sights any longer so I put a #7194 model on a Cherokee. Had to add a taller fiber front sight... .490 maybe? Anyway, about 1/2 to 3/4 inch groups at 25 yards and often three touching holes. Finding a Seneca/Cherokee sight, which is smaller, is multitudes harder than finding a #7194.
I've bought five of the peeps over the years, two are laying around and I am contemplating buying a couple more Cherokee/Seneca tangs to swap out on my .36 and .45 Senecas. There is a guy on ebay that has a number of in-the-white tangs for those models. He might have spares for the Renegades and Hawken as well.
If you are going to drill/tap a tang, I would suggest buying a spare and mounting on that one, save your original just in case something goes wrong. I pulled it off... once... so either I got lucky or it isn't that hard to do.
I picked one up this summer in a box on a auction sold off most of the stuff I didn't have any use for and am currently into it for about half of the going ebay price for a new in box one just haven't gotten around to installing it. the disadvantage to the TC is it not easily removed if you want to use the irons in a match it's planed to go on my light bench ( TC Renagade 50 with the round ball barrel that is currently wearing a 57ml )
Ditt44
40 Cal
Those images show adding two screws. On any side-lock, you use the lower tang screw in the bottom hole and drill and tap a hole below the upper/top tang screw. So your sight only requires you to drill ONE hole, not two.
Last edited:
Yep, only one hole needs be drilled and tapped. However, by installing a TC peep according to those directions, it should help by not having to raise the peep as high for a conical. In short, the peep would be mounted a little higher that way. I chose to use the existing rear tang screw as the rear hole for the peep mount. Thus, I only had to drill and tap one hole for the forward peep mount screw. It works.
Last edited:
That second image is for a TC Contender.
the instructions cover most of the T/C models just doesn't show pictures for every one but if you look it says traditional cap or flint lock muzzleloaders
- Joined
- Feb 24, 2019
- Messages
- 211
- Reaction score
- 96
I was having a problem seeing the sights on my period correct Kibler Woodsrunner
I mounted a TC peep on the tang and a globe style front sight
I’m now able to shoot my Kibler , and plan on taking a deer with it this season
Better than leaving it home in the corner..
I mounted a TC peep on the tang and a globe style front sight
I’m now able to shoot my Kibler , and plan on taking a deer with it this season
Better than leaving it home in the corner..
Indeed it does. However, that second picture is of a TC Contender.
If you decide to only drill and tap one hole, as I have done, to mount a TC peep, it can be removed in about one full minute. That way you can still use your blade sight (as you contend you are interested in doing) IF the TC peep will work with it in the way. Personally, I do not understand how it could work like that. A peep can be very accurate if the aperture is of proper size for the front sight.
Last edited:
