What do you guys lube your C&B revolvers with?

[Surrywoodman]

All,
I just got a Pietta 1851 Navy in 44 cal. brass frame that I gave $80 for. It seems to be close to pristine and the guy only shot it a few times until he had a chain fire which freaked him out. I used to have a Navy and Army many moons ago but sold them. Back in the day I used crisco but after a couple of shots it became a mess. Does anyone have an over ball lube that does not disintegrate too badly? I have read where folks used crisco/bees wax...looking for what you use that gives success. I am not really interested in wads but I am willing to consider, never have used them.

 

[Phil Coffins]

I use wads, when I used grease over the ball after the first shot most of the grease was blown off the other chambers.

 

[French Colonial]

I use wads, when I used grease over the ball after the first shot most of the grease was blown off the other chambers.

And made a mess all over the gun!

 

[wiscoaster]

Wads are great for the convenience factor.

 

[Gtrubicon]

I don’t lube r my revolvers. I use 454 balls.

 

[Jappo]

I don’t lube r my revolvers. I use 454 balls.

I don't either. I also use the 454. I do lube my my Walker arbor/cylinder before shooting. 50gr or more are notorious for gumming up rotation.

 

[Salty]

I do use wads lubed with water to Ballistol 7:1 then dried in the sun. I also use 454 balls in my Pietta 1858 Rem. Only 15 gr of Schuetzen 3f. Reasonably accurate at 15 yds.

 

[Old Hawkeye]

Lube over the loaded cylinder is a waste of time & money as well as messy. Lubed wad under the ball, a proper size ball & nipples that provide a good tight fit of the caps is all I do. Never had a chain fire. It's more likely your friends chain fire was caused by poor nipple to cap fit than anything else.

 

[Jappo]

Only chain fires I've had were from LeMats. I used .451s and they were tight. But they still worked loose under recoil. Tried .452, had to remove the cylinder and a rod to load them up. They still worked loose. Had another chain fire. Bought another and the same thing. And besides the balls working loose, the timing was off on both of them. The ball was hitting the side of the barrel. Its impossible to time one because of the way they are made.

 

[Sparkplug]

For RB I use a wad. Non lubed for long term and lubed if I know it will be shot soon. For conicals I just use whatever lube I have in the grooves. I have found Burts Bees original chapstick to do quite well.

 

[KingOfKindling]

I use nothing, just ball/conical and powder. Life is to short to mess with applying wads or gobs of grease for no good reason. I use the guns like they were meant to be used.

Use the proper ball size, and make sure your caps fit the nipples you're using, and there will not be a problem.

 

[Taevers]

All,
I just got a Pietta 1851 Navy in 44 cal. brass frame that I gave $80 for. It seems to be close to pristine and the guy only shot it a few times until he had a chain fire which freaked him out. I used to have a Navy and Army many moons ago but sold them. Back in the day I used crisco but after a couple of shots it became a mess. Does anyone have an over ball lube that does not disintegrate too badly? I have read where folks used crisco/bees wax...looking for what you use that gives success. I am not really interested in wads but I am willing to consider, never have used them.

https://geojohn.org/BlackPowder/RevolverMobile.html