It says on their website to call to order.
I think number for buckshot and the 22 air gun slugs are your best bet other than the factory made ammo.
Who has derringers?
- Thread starter SwampBilly
- Start date
Help Support Muzzleloading Forum:
I think number for buckshot and the 22 air gun slugs are your best bet other than the factory made ammo.
I was looking to see if they sold the 777 in a ffffg granulation but evidently the fffg is the smallest they produce.
I went ahead and splurged on a pound of ffffg swiss. Figured that will last me the better part of forever.
I have several NAA Companion revolvers in different barrel lengths, and a couple of Freedom Arms as well. They are very precise, and extremely well made. I have found 3f is best to use, as 4f seems to escape through the nipples before capping. #4 buckshot is Dandy for plinking, while the factory bullets are nicely made and very affordable.
If you're a diehard caster, you can buy a mould from .22 reloader. Their mold is 2 cavity and makes both short and long rifle style heeled bullets.
These little guns are simply tons of fun.
If you're a diehard caster, you can buy a mould from .22 reloader. Their mold is 2 cavity and makes both short and long rifle style heeled bullets.
These little guns are simply tons of fun.
Can't wait to get mine this coming week. Perhaps maybe one grain of 3F down in the bottom and the remaining three grains 4F?
That shouldn't do anything dangerous should it?
No, not at all.
Oh and for what it's worth, I use a tad of Alox lube over the ball when I'm using round balls (#4 buckshot). #4 is a really tight fit, but it's buckshot, not a precision round ball. With that in mind, it's good cheap fun shooting. The bullets from NAA perform better. And yes, you can achieve good results.
Oh and for what it's worth, I use a tad of Alox lube over the ball when I'm using round balls (#4 buckshot). #4 is a really tight fit, but it's buckshot, not a precision round ball. With that in mind, it's good cheap fun shooting. The bullets from NAA perform better. And yes, you can achieve good results.
I was thinking these could work pretty good. Almost 30 g and they have a dish shape base so they should probably obturate very well.
They also appear to have a very good hollow point and they are slug shape. Certainly not your typical air gun pellet. I'm just wondering about the fact that they are 5.5 mm diameter and the bore of a 22 is 5.6 mm.
While it doesn't seem like much.... As far as a cap and ball application, 1/10 of 1 mm could be significant.
Just some alternative that could be used in a pinch.
They also appear to have a very good hollow point and they are slug shape. Certainly not your typical air gun pellet. I'm just wondering about the fact that they are 5.5 mm diameter and the bore of a 22 is 5.6 mm.
While it doesn't seem like much.... As far as a cap and ball application, 1/10 of 1 mm could be significant.
Just some alternative that could be used in a pinch.
The biggest problem with the airgun pellets for a cap and ball is the size simply because of the fit in the cylinder.
They're fine if you load only one shot. But if you load more than one chamber they do not fit tightly enough to stay put when the gun goes off. This will most like result in a chain fire. Full sized revolvers are bad enough, but mini revolvers can more easily put a couple into the shooter because they're so small and more difficult to hang on to.
Otherwise, those look like really good projectiles.
They're fine if you load only one shot. But if you load more than one chamber they do not fit tightly enough to stay put when the gun goes off. This will most like result in a chain fire. Full sized revolvers are bad enough, but mini revolvers can more easily put a couple into the shooter because they're so small and more difficult to hang on to.
Otherwise, those look like really good projectiles.
Another note;
A tip on how to hold the mini was shared by their designer, Mr. Casull.
It might look like an overcooked way to hold them, but it works.
If you hold the gun in the strong hand, basically pinching the grip between the thumb and index finger, and use the off-hand thumb and index finger to cock the hammer and pull the trigger. The results are a more stable hold and a better result on the target.
The attached photo is of a 4" Companion in action being held as described.
A tip on how to hold the mini was shared by their designer, Mr. Casull.
It might look like an overcooked way to hold them, but it works.
If you hold the gun in the strong hand, basically pinching the grip between the thumb and index finger, and use the off-hand thumb and index finger to cock the hammer and pull the trigger. The results are a more stable hold and a better result on the target.
The attached photo is of a 4" Companion in action being held as described.
Attachments
APG
45 Cal.
10-4
I wonder about the feasibility of the 25 caliber ones? I wonder if the loading lever could swage them in for a tight fit?
You know us muzzleloaders, always thinking about alternatives for supply chain issue.
If it did swage them in, I'm sure a good chunk of lead would be shaved off.
Talked to the girl at NAA yesterday on the phone and she said they just ran out of the bullets and have re ordered, they expect them back, in about 3 to 4 weeks.
My pew pew is coming tomorrow. The 250 that come with the kit should easily last me that long.
Have to order me about 750 or 1,000 when they come in.
- Joined
- Jun 17, 2019
- Messages
- 8,399
- Reaction score
- 9,814
Yikes! Wish they were still around! Very attractive!
That's all they are designed for. And quite effective at that.
Really?? It's an antique firearm. It's gonna have wear/tear.Looks real quality! Check out the screw-head, though...did the original purchaser get a dedicated turn-screw with it?
I just got one of the NAA companion super cap and ball 22 revolvers. They cost a premium but they are very nice. 100% stainless except for the grips
I have a Lincoln gun. 5 grain of 3F and a 15 thousands patch. It is good up two 10 feet to cut paper.
