• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Lock coming loose during shooting.

shop deals on amazon
the hawken shop
Shop deals on ebay
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
C

Chris Myers

32 Cal
Joined
Apr 10, 2021
Messages
34
Reaction score
5
Location
stl
I have just finished my Hawken 50 cal and shot 7 shots through it. So nice of a weapon. So nice. Now when i went to clean it i saw the front of the lock came out about 1/16th of an inch. Did i do something wrong? It works well but just noticed it. ANyone know if i can secure it somehow so it does not move. When building it was tight but not to tight. Do i need to just tighten up the lock bolt. Duh!!! ill look at that now!

THank you
Chris
 
No but im not sure I tightened it down fully when finishing it up. I'll check on it and see. If I did tighten down and it came loose I'll use lock tight. Thnks
 
Just apply a little drop of the removable type don't go overboard with the stuff.
 
Chris Myers said:
Now when i went to clean it i saw the front of the lock came out about 1/16th of an inch. Did i do something wrong?
Click to expand...
Chris Myers said:
If I did tighten down and it came loose I'll use lock tight.
Click to expand...
I would not think you would need or want to use Loctite on a lock bolt, something that gets removed frequently. Better to correct the problem. There is a good chance that lock/lock bolt were not full seated before you started shooting. You might want to tap the bolt head lightly with a plastic hammer or screwdriver handle and see if anything moves. Then when you go shooting the next time, check that lock bolt after each shot.
 
SDSmlf said:
I would not think you would need or want to use Loctite on a lock bolt, something that gets removed frequently.
Click to expand...
No problem using blue Loctite on bolts that needed to be "removed frequently". Not the best solution, better to do as @SDSmlf recommends, but if nothing else works, don't rule out the Loctite. I'm one of those that plays "musical chairs" with Magpul accessories and with optics, so I deal a lot with blue-Loctited screws. No worries. Can be done.
 
Chris Myers said:
I have just finished my Hawken 50 cal and shot 7 shots through it. So nice of a weapon. So nice. Now when i went to clean it i saw the front of the lock came out about 1/16th of an inch. Did i do something wrong? It works well but just noticed it. ANyone know if i can secure it somehow so it does not move. When building it was tight but not to tight. Do i need to just tighten up the lock bolt. Duh!!! ill look at that now!

THank you
Chris
Click to expand...
Wood shrinks and shi_ also happens. Make sure your wood base is parellel to the lock plate when fully in place. If it is not, you can get a teeter totter effect. Might have to shim a tad or remove a small bump. If the machine screws are properly threaded all you should need is to snug them up.
I have been shooting since the 70s and never used lock tight.
Good luck,
Larry
 
Larry (Omaha) said:
Wood shrinks and shi_ also happens. Make sure your wood base is parellel to the lock plate when fully in place. If it is not, you can get a teeter totter effect. Might have to shim a tad or remove a small bump. If the machine screws are properly threaded all you should need is to snug them up.
I have been shooting since the 70s and never used lock tight.
Good luck,
Larry
Click to expand...
Thank you
 
Chris Myers said:
I have just finished my Hawken 50 cal and shot 7 shots through it. So nice of a weapon. So nice. Now when i went to clean it i saw the front of the lock came out about 1/16th of an inch. Did i do something wrong? It works well but just noticed it. ANyone know if i can secure it somehow so it does not move. When building it was tight but not to tight. Do i need to just tighten up the lock bolt. Duh!!! ill look at that now!

THank you
Chris
Click to expand...
Thanks for those who replied. Apperantly when assembling it i did not tighten down the lock enough. it works fine now.
 

Similar threads

Jappo
Unknown Flintlock pistol
Replies
15
Views
636
PathfinderNC
PathfinderNC
H
Flint works loose after multiple shots
2 3
Replies
46
Views
3K
MAC1967
MAC1967
T
Pedersoli flintlock not cocking
2
Replies
31
Views
947
westrayer
W
SammyP
Need help tuning lock
Replies
13
Views
779
rich pierce
R
R
  • Locked
SOLD Victorian Era Flint Pistol Copy
Replies
12
Views
600
rickystl
R

Latest posts

Back
Top