have been using light-type gun oil on the arbor of my colt open-topped revolvers. want switch to something more viscous. what do you like? thx for comments
lp
lp
arbor grease
- Thread starter lone pine
- Start date
Help Support Muzzleloading Forum:
- Joined
- May 22, 2008
- Messages
- 628
- Reaction score
- 1,115
Works real well
Phil Coffins
69 Cal.
Mobile One, simple, easy and commonly available.
I'm using the same beeswax-mixture chamber/bore/bullet/patch lube I use for everything and every use.
Greenjoytj
54 Cal.
Try several brands of grease to find what work for you.
Choose a synthetic oil based grease because synthetic oil has an affinity for metal it likes to stick to metal and not run off.
I use Rand H.A.W.G. It works great for me but I don’t recommend it do ito it’s availability seem to have disappeared.
That Mobile 1 grease would be a good grease as recommended by above poster.
Lucas Red and Tacky would likely be equivalent.
The only thicker oil I would not recommend is M-Pro 7 LPX Gun Oil, it has so much fine teflon dust in it it takes considerable shaking to get liquefied after sitting for weeks. Plus teflon doesn’t seem to be an additive that recommended to be used on firearms. The shear strength of this oil really slowed cylinder rotation speed.
The one positive of the LPX oil is for use on the outside surface of the firearm, wipe it on the wipe off it leaves the surface feeling dry but very very slick.
Choose a synthetic oil based grease because synthetic oil has an affinity for metal it likes to stick to metal and not run off.
I use Rand H.A.W.G. It works great for me but I don’t recommend it do ito it’s availability seem to have disappeared.
That Mobile 1 grease would be a good grease as recommended by above poster.
Lucas Red and Tacky would likely be equivalent.
The only thicker oil I would not recommend is M-Pro 7 LPX Gun Oil, it has so much fine teflon dust in it it takes considerable shaking to get liquefied after sitting for weeks. Plus teflon doesn’t seem to be an additive that recommended to be used on firearms. The shear strength of this oil really slowed cylinder rotation speed.
The one positive of the LPX oil is for use on the outside surface of the firearm, wipe it on the wipe off it leaves the surface feeling dry but very very slick.
thanks. all good info.
yes. going to start with John Deere grease and work w/couple of other suggestions. intrigued with the stp suggestion.
lp
lp
Lubriplate lithium grease
yep. trying a variation of that when I get it tomorrow. thx to all for comments.
lp
lp
Not really a thing. NLGI 2. For motor bearings as well as other use, yes, they are all rated to 300 some degrees (heating bearings to install aka friction fit, requires about 250 degrees - so by default the grease has to be good to 300+)
Synthetic by its nature is higher temp, also by its nature it does not get stiff as it gets cold. That is the type to use. Matter hot who the mfg is.
45D uses Mobile One, good stuff. Super Lube per RiverRat also uses Super Lube synthetic and equally as good. I happen to use it as I got free samples from days of yore.
Frankly I don't know of any synthetic grease mfg that is not good, if they go to the trouble to synthetic, by its nature its a higher cost grease and is not worth going half way.
No question regular grease works fine. Synthetic is just better.
ernbar
45 Cal.
Read somewhere using Pam cooking spray so I did and works really good.
yes. I need high temp grease on my arbor cause I fan my gun so fast the arbor heats up
Wheel grease is not motor bearing grease and synthetic deals with all of it.
- Joined
- Mar 5, 2010
- Messages
- 743
- Reaction score
- 377
I just use my homemade Bore Butter. Works well enough for me and cleans up a lot easier than petroleum products.
