Independant Tests?? - 2 come to mind: 1 run in a British magazine and one done by a local shooter here: They were pretty much the same: 3 pieces of clean - degreased steel: 1 a control; 1 with a quantity of Black Powder burnt on it and the 3rd with a similar quantity of Pyrodex burnt on it. The pieces were then left to see what would happen- I can't remember the time intervals at which the local guy checked the pieces but at the end the control had a light specking of rust as you would expect from unprotected steel; the BP sample had an even coat of light rust with no pitting; Pyrodex had caused flakey rust with deep pitting. As for temperature my reading leads me to believe that BP burns at 1300 - 1500 degrees C and Pyrodex at about 4500 Degrees. As I said; fastidious cleaning will help if you have to use Pyrodex.
-
Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.
We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.
Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103
A question about pyrodex
- Thread starter Sir Boniface Harrison
- Start date
Help Support Muzzleloading Forum:
Respectfully, barrels are made of steel, which melts at temperatures between 1371 and 1540 degrees Celsius, or 2500 - 2800 degrees Fahrenheit.
4500 degrees for Pyrodex? Are we sure about that? Seems like there wouldn’t be much barrel left to clean.
Notchy Bob
4500 degrees for Pyrodex? Are we sure about that? Seems like there wouldn’t be much barrel left to clean.
Notchy Bob
We need to go back to 2009 when this topic was previously discussed on the Forum. Do pay attention to the temperature units as some of the posters play fast and loose with Fahrenheit and Celsius degrees.
https://www.muzzleloadingforum.com/threads/ignition-temperatures.44590/
What should concern us is the ignition temperature of the powders and a little less on what the burning temperature is.
While there are some differences on what the ignition temperature of black powder is the black powder temperature of ignition is markedly lower than that of Pyrodex or Triple 7.
Now back to address @Sir Boniface Harrison's concerns, if only Pyrodex is available for use in his percussion firearms, then Pyrodex or Triple 7 can be used. Knowing that these substitutes require a higher ignition temperature than black powder, he should be using a nipple designed to send more heat to the powder charge, a percussion cap that delivers more heat to the powder charge such as a magnum cap or the RWS 1075 Plus or a duplex load of about 5 grains or black powder. Or all of the previous.
The precaution that must be followed is the cleaning as soon as possible of the fouling from the firearm. The fouling from the substitutes can be cleaned with the water and soap cleaning regimen we use for black powder. He should do a quick wipe of the fouling at the range to start protecting the bores if deep cleaning is prohibited at his range.
https://www.muzzleloadingforum.com/threads/ignition-temperatures.44590/
What should concern us is the ignition temperature of the powders and a little less on what the burning temperature is.
While there are some differences on what the ignition temperature of black powder is the black powder temperature of ignition is markedly lower than that of Pyrodex or Triple 7.
Now back to address @Sir Boniface Harrison's concerns, if only Pyrodex is available for use in his percussion firearms, then Pyrodex or Triple 7 can be used. Knowing that these substitutes require a higher ignition temperature than black powder, he should be using a nipple designed to send more heat to the powder charge, a percussion cap that delivers more heat to the powder charge such as a magnum cap or the RWS 1075 Plus or a duplex load of about 5 grains or black powder. Or all of the previous.
The precaution that must be followed is the cleaning as soon as possible of the fouling from the firearm. The fouling from the substitutes can be cleaned with the water and soap cleaning regimen we use for black powder. He should do a quick wipe of the fouling at the range to start protecting the bores if deep cleaning is prohibited at his range.
Last edited:
- Joined
- Jul 8, 2019
- Messages
- 3,145
- Reaction score
- 5,635
Being the explosion that takes place in the barrel of a rifle is less that a second the heat is minor. If you shoot many rounds one behind another heat will build up but not very much considering how hot the flash heat is?
@Bucks Co no offense, but the hot gas is only in there for milliseconds - it and the patch and ball are gone before significant heat transfer to the barrel can take place. That's why there is no significant difference in effects on recovered patches between the two regardless of what the actual stoichiometric gas temperature is.
Edited to add: Sorry @LME - didn't see your post! You said it first!
Last edited:
Antelope Pete
40 Cal
20 plus years ago for hunting I would put a dry patch down first. If I used Pyrodex it would commonly burn the patch and sometimes it would be smoking on the ground so I quit doing that. B.P. didn't do that.
It's called a duplex load aka BP in breech with something else atop it!
Another overblown thread on Pyrodex...well the pages here have to be filled with something...
I put in a musket nipple and started using musket caps and haven’t had any problems with Pyrodex
Ready to make some smoke!
@Frontier's, if your only propellant is that bottle of Pyrodex and you don't have some real black powder to use as a kick starter in the bore and in the pan in that flint lock rifle, then you may be preparing for some failure to fire and demonstrating how to pull a ball from a charge that won't fire.
Iirc Black powder has an ignition temperature of 350 degrees and pyrodex about 600 degrees, so in a say 60 grain load if the first 10 grains were fffg that should work well for igniting the pyrodex but it would be a little pita .
longcruise
70 Cal.
I think the ignition temperature is closer to 450f but that is irrelevant to your advice. A ten grain BP charge under the Pyrodex should be very effective.
I'll add that my DIY caps are noticeably hotter than commercial caps and I suspect that they would set off any of the subs without a hitch. No help their for a flintlock though.
