Got the permalyn lid off, First coat of finish on!
- Thread starter koauke
- Start date
Help Support Muzzleloading Forum:
CuNosecap
45 Cal.
I think that is a shipping lid. Drive a flat screwdriver blade through lid then pry lid up and discard. The other lid is for typical use.
CuNosecap
45 Cal.
As an alternate, use a screwdriver and punch a couple of hole to pour from, leaving the lid in place. This approach minimizes open top surface area. But ultimately, just poke, punch and discard.
koauke
40 Cal.
- Joined
- Jun 14, 2014
- Messages
- 181
- Reaction score
- 158
Awesome, thanks! Got it!
CuNosecap
45 Cal.
Maybe getting the lid off was the hardest part of your Kibler build?
Just kidding! It looks fantastic. Nice work.
Rick
Just kidding! It looks fantastic. Nice work.
Rick
koauke
40 Cal.
- Joined
- Jun 14, 2014
- Messages
- 181
- Reaction score
- 158
Interesting, the wood darkened up quite a bit as the finish dried. Its almost a deep chocolate. Suppose there is no way to lighten it at this point. Bit darker than I had hoped for, guess I will know for the next time. Or will retain that original color when the finish was first applied as the finish builds up with additional coats?
You can always adjust or change it. If you think what you have is too dark, you can use a piece of maroon Scotchbrite pad, or sandpaper. Dip them in the finish and as you apply a coat, rub it out and lighten areas or the whole stock. Just take it slow.
koauke
40 Cal.
- Joined
- Jun 14, 2014
- Messages
- 181
- Reaction score
- 158
Thanks for the suggestion.
I plan to put a coat of finish in the inlets and what not but according to Kibler iron nitrate can cause rust problems on the metal parts if used in the inlets. He also noted that originals were not stained in the inlets or areas not seen.
I plan to put a coat of finish in the inlets and what not but according to Kibler iron nitrate can cause rust problems on the metal parts if used in the inlets. He also noted that originals were not stained in the inlets or areas not seen.
If you use a nail and poke a hole in the lid what's left in the can will last a lot longer. This works great for Tru Oil and I suspect it will work for Permalyn.
I found that after a few months the lid on my Permalyn can was permanently welded on by the dried finish. I ended up opening the bottom with an old fashioned can opener (that makes the triangle holes) and poured the unused half of the can into an old mushroom jar I had a lid for.
Stain isn't generally applied to the inlets because the aqua fortis that most people used on the originals, and yet today, will rust metal things when in long contact with that type of stain. Best to just apply some finish to those areas.
koauke
40 Cal.
- Joined
- Jun 14, 2014
- Messages
- 181
- Reaction score
- 158
Got the second and third coats of permalyn sealer on today. I was concerned after that first coat dried so dark. Its still dark, but does look very nice.
Here are a couple pics after the third coat this evening in the evening sun. Thinking maybe one or two more coats?
Here are a couple pics after the third coat this evening in the evening sun. Thinking maybe one or two more coats?
That's looking very nice!
Will there be an oil or varnish as a topcoat, or is Permalyn the final product? (I'm clearly unfamiliar with it.) If so, you might notice a "lightening" effect by the amber tint or an increase in reflectivity/gloss. Sometimes an oil finish will act as a solvent and lift some of the darkness as you rub it in & wipe off the excess.
Again, I am not familiar with Permalyn...yet.
To help keep the remaining finish from hardening in the can, I typically take a deepish breath, hold it for a bit, then exhale into the container (without spitting!), then immediately slap the lid on it. I do this with all reactive finishes except latex paint.
The idea is that reactive finishes react with the oxygen in the air and transform into a new substance that is solid and resistant even to its own original solvent.
By exhaling into the container, one drives out the ambient atmosphere with its oxygen and replaces it with carbon dioxide. CO2 is inert and won't let go of any oxygen for the finish to react with. Even if you couldn't fill the can with your exhalation, CO2 is heavier than the N-O-and other stuff too-atmosphere and lays on top of the liquid like a blanket, shielding it from reaction.
Since I started doing this, I have oils and poly and paints that are up to a decade old and don't even have that rubbery or solid "disk" of hardened finish on top when I open the container.
I'll be looking forward to your range report!
Will there be an oil or varnish as a topcoat, or is Permalyn the final product? (I'm clearly unfamiliar with it.) If so, you might notice a "lightening" effect by the amber tint or an increase in reflectivity/gloss. Sometimes an oil finish will act as a solvent and lift some of the darkness as you rub it in & wipe off the excess.
Again, I am not familiar with Permalyn...yet.
To help keep the remaining finish from hardening in the can, I typically take a deepish breath, hold it for a bit, then exhale into the container (without spitting!), then immediately slap the lid on it. I do this with all reactive finishes except latex paint.
The idea is that reactive finishes react with the oxygen in the air and transform into a new substance that is solid and resistant even to its own original solvent.
By exhaling into the container, one drives out the ambient atmosphere with its oxygen and replaces it with carbon dioxide. CO2 is inert and won't let go of any oxygen for the finish to react with. Even if you couldn't fill the can with your exhalation, CO2 is heavier than the N-O-and other stuff too-atmosphere and lays on top of the liquid like a blanket, shielding it from reaction.
Since I started doing this, I have oils and poly and paints that are up to a decade old and don't even have that rubbery or solid "disk" of hardened finish on top when I open the container.
I'll be looking forward to your range report!
koauke
40 Cal.
- Joined
- Jun 14, 2014
- Messages
- 181
- Reaction score
- 158
I'm just following what Jim said in his video demonstrating the finishing process on a woodsrunner. According to him Permalyn Sealer can be used as the final finish. I guess its the same as the Permalyn Finish, just thinner. I'm totally new to this, so just following his suggestions in the videos.
I'm gonna say that's probably The Best course of action!
And now I know more about Permalyn.
Looks beautiful.
I wouldn’t lighten it, it looks right (good) as is.
Ditto... Purrrrdy....
