I don't know about a rebore with rifling, as I'm sure that is the more expensive route. But I just had him ream a .54 renegade to .56 smooth bore and it was 75 bucks.
Help ID + Condition Please - Pedersoli Rifle
- Thread starter muzzleloadershooter
- Start date
Help Support Muzzleloading Forum:
By the time you ship it and get it worked on and shipped back, your a good $200 in to the gun for a reline or re rifle. Going to smoothbore is a little cheaper...just depends on what you're looking for and how much you want to spend.
If it were me, I'd clean it first, as suggested above. It may shoot just fine with a few hours of cleaning invested. I have a smoothbore with a frighteningly ugly bore that will cloverleaf shots at 25 yards, you never know.
If it were me, I'd clean it first, as suggested above. It may shoot just fine with a few hours of cleaning invested. I have a smoothbore with a frighteningly ugly bore that will cloverleaf shots at 25 yards, you never know.
- Joined
- Jun 17, 2019
- Messages
- 8,399
- Reaction score
- 9,816
I saw at a small show, a Lyman flinter with a horrible bore! Yet a high price, as though the bore never matters. Many do not know anything about maintaining a muzzle loader.
- Joined
- Aug 14, 2019
- Messages
- 164
- Reaction score
- 216
Clean it up and shoot it. If it doesn't group well, buy a reamer and make it into a smooth bore. I have an old Dixie PA rifle kit that would never shoot round ball consistently. I purchased a hand reamer and cut out the poor excuse of rifling. Took me a while but now I have a small bore shotgun.
- Joined
- Jun 17, 2019
- Messages
- 8,399
- Reaction score
- 9,816
Someone needs to invent or find a stiff-ish metallic "pipe cleaner" that is firm enough to go in and out of Flash Channels. There must be something similar out there in the world of machinists or similar.
kelvinator
32 Cal.
Looks some nice figure in the stock on that one.
If I got or could get it cheap, I'd have to give a go at cleaning, scrubbing and polishing the bore and flash channel as described above.
If I got or could get it cheap, I'd have to give a go at cleaning, scrubbing and polishing the bore and flash channel as described above.
- Joined
- Mar 13, 2020
- Messages
- 7,495
- Reaction score
- 21,014
- Location
- On the Border in Idaho looking at BC
from the pictures i would invest some time and energy (both of which i am in short supply) in cleaning up that bore with scotch brite pads and some metal polish. i have shot worse and had them accurate. fouling can be overcome with swabbing after each shot. just takes a few seconds.
deer creek sells a clean out screw replacement that comes with a small wire brush for cleaning the flash channel
I have a bit of experience with Pedersoli and find them to be very nice people to deal with, they answer my emails usually within a day or two. You have a beautiful stock on the rifle and with the serial number Pedersoli can tell you the model and when it was built. They can also quote you on a new barrel if you find the need to go that way. Please note that all of Italy ( and a good part of Europe) will be going on summer vacation in the next week or so, so emails will take a bit longer after next week.
sportster73hp
50 Cal.
- Joined
- Jan 16, 2020
- Messages
- 1,031
- Reaction score
- 803
I would try cleaning it first. I have an original Enfield that was white with corrosion and it cleaned up. Thought maybe it was a smoothbore before cleaning. With a 20 inch barrel distance shooting is out but 25 and 50 yards it will group.
Never know just how 'bad' something is until you disassemble it.
Never know if it can be cleaned up until you try.
Never know if it can be cleaned up until you try.
Let me know if you want to sell it.
