• Friends, our 2nd Amendment rights are always under attack and the NRA has been a constant for decades in helping fight that fight.

    We have partnered with the NRA to offer you a discount on membership and Muzzleloading Forum gets a small percentage too of each membership, so you are supporting both the NRA and us.

    Use this link to sign up please; https://membership.nra.org/recruiters/join/XR045103

Just got a pedersoli side by side 12 gauge

Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Johnny, if them over powder cards are tight you might break your rammer.
Just stamp thin cards.

Cut the fibre wads in half. Make them go twice as far!
Hiya mate, good to see another from the land of the over priced and over taxed!😁👍

Yep thank god for Messrs Henry Krank, got a few bits and bobs en-route including an aluminium loading rod and cleaning kit (read load pulling worm and nick knacks😜) full speed through the post office.
Was going to keep the original bit of stick in place for decoration😆🤔

Just need it to dry up a bit here, my shooting/ hunting permissions are underwater at the moment and wellington boots are not going to cut it!!
 
I saw a guy on you tube using a 3/4 punch and punching from empty soda can boxes.

Have you guys tried this?
Hiya bud, I have got a 3/4 punch and was rummaging through the rubbish looking for suitable material to make holes in when the memory bank kicked in and lo buried in the garage was a whole sack of loading components from yesteryear when I used to reload 12 bore cartridges.
Loads of thick powder cards and felt wads in all lengths, and as Brit above says I'll cut those down to suit👍

I did thumb in a couple of the powder cards about half an inch below the muzzles and then capped up and popped a couple.

Good to see those cards positively fly out and whack the wall so good to know the nipples are open and fire finding its way inside😎
 
Just had another squint 👀 at mine and apart from all the other proof and ident marks there is a boxed AD stamp, am I right in deciphering year of manf as 1991??

Looks to have lead a charmed life, barrels are shiny from base plugs to muzzle. Chromed??

Barrel wedge needs a positive tap to shift it and the locks although not corroded in any way were drier than the moon and squeaky.

Given them a blast of Napier gun cleaner to wash out any dust and possible firing residues and a squirt of Browning gun lube.

Left to drain overnight on a paper towel and blown them out with the air line to chase any excess away, cocks nicely and quietly now after its treat👍😆
 
Given them a blast of Napier gun cleaner to wash out any dust and possible firing residues and a squirt of Browning gun lube.
Reconsider using that stuff, it reacts badly to black powder residue! It will NOT protect anything.
Get some beeswax, or coconut fat and gently melt it. Once melted add some olive and allow to cool. Adjust the mix to your satisfactory consistency.
That WILL protect the gun.

The barrels are chrome plated for corrosion resistance, not to facilitate the use of steel shot.
 
Arrived today hotfoot from Henry Kranks fine emporium of all things muzzle loading here in the UK

Nice steel loading/ cleaning set with a natty pouch to keep everything together👌

Nice muzzle filling rammer head to prevent cards flipping over on their journey down the pipe😎

Please excuse the red wine rack😁
IMG_20240928_125332.jpgIMG_20240928_125342.jpgIMG_20240928_125423.jpgIMG_20240928_133056.jpgIMG_20240928_133118.jpgIMG_20240928_133123.jpgIMG_20240928_133157.jpg
 
Reconsider using that stuff, it reacts badly to black powder residue! It will NOT protect anything.
Get some beeswax, or coconut fat and gently melt it. Once melted add some olive and allow to cool. Adjust the mix to your satisfactory consistency.
That WILL protect the gun.

The barrels are chrome plated for corrosion resistance, not to facilitate the use of steel shot.
Balistol oil any good, I use so much of it, it's almost like an aftershave🤯😆😆
 
Reconsider using that stuff, it reacts badly to black powder residue! It will NOT protect anything.
Get some beeswax, or coconut fat and gently melt it. Once melted add some olive and allow to cool. Adjust the mix to your satisfactory consistency.
That WILL protect the gun.

The barrels are chrome plated for corrosion resistance, not to facilitate the use of steel shot.
You Sir, need to write a book. I’d be in for a copy. Technical data along with anecdotes, pics of your adventures and of course the pup.
 
If you have some scrap barrel lengths they can be sharpened up to make a punch, or a rotating cutter if the barrel wall is thin. Probably easier to just buy one tbh, but if we wanted to do things the easy way we'd be in a different forum I think.

I've had decent results with a square load in skychief configuration.
Powder, overpowder card, shot, and then an overshot card and a saturated oily fibre wad both rammed down together. It can get a bit messy. Fine for hunting but with clays it's just too darn oily after a few shots

I use a 28 gram plastic cup wad as a measure. If memory serves that was 68-70 grains henry krank medium. This patterned well enough for me and I've not got round to doing any further development.
 
Back
Top