What Muzzleloading Stuff Did You Do Today?
- Thread starter PathfinderNC
- Start date
Help Support Muzzleloading Forum:
64Springer
75 Cal.
The brass nose cap and now the stock slopinflop trigger have been round filed.
Made maple inserts to serve as a trigger well. Still using the stock trigger plate. It was pinched a tad to lessen side to side play.
TOTW trade gun trigger drilled for .093 pin and installed. Love me some trade gun triggers. No more slopinflop.
Also made a maple lock mortise plate to beef up the area. Traditions cuts WAY too much material out of their mortises.
Inletted the plate so all the various goodies could nestle into it.
Everything from this point forward is a cakewalk.
Made maple inserts to serve as a trigger well. Still using the stock trigger plate. It was pinched a tad to lessen side to side play.
TOTW trade gun trigger drilled for .093 pin and installed. Love me some trade gun triggers. No more slopinflop.
Also made a maple lock mortise plate to beef up the area. Traditions cuts WAY too much material out of their mortises.
Inletted the plate so all the various goodies could nestle into it.
Everything from this point forward is a cakewalk.
Attachments
Last edited:
Shot Kibler SMR at 50 yds to zero new sights - successful:
https://www.muzzleloadingforum.com/threads/what-sight-for-kibler-smr.168744/page-2#post-2444762Also shot Queen Anne pistol at 7 yds just just to see if I could hit the paper with a short-barrel smooth bore without any sights. Ehhh....out of five shots only four even hit a 17 inch target. Good range conversation piece, though, and that's about all it's good for IMO.
https://www.muzzleloadingforum.com/threads/what-sight-for-kibler-smr.168744/page-2#post-2444762Also shot Queen Anne pistol at 7 yds just just to see if I could hit the paper with a short-barrel smooth bore without any sights. Ehhh....out of five shots only four even hit a 17 inch target. Good range conversation piece, though, and that's about all it's good for IMO.
Last edited:
Old Sparky
40 Cal
It really only applies to pistols as far as the advice on there. But I have used it many times and it definitely helps
Spent 2 hours casting .310, .400, .457 & .530 balls - have to replace my .400 & .530 molds with 2 cavity - so slow doing 1 ball at a time!
Very nice. Looks great. I’d pack that around. 
Punched more holes…
I just finished a rifle for, 'Sitting Fox Muzzleloader'. It's in the white.
38" 'C' wt. Colrain Barrel, .45 cal.
M4 Sugar Maple Stock
14" LOP
53.5" Total Length
9.9 pounds
Brass Furniture
RE Davis Continental Flintlock
38" 'C' wt. Colrain Barrel, .45 cal.
M4 Sugar Maple Stock
14" LOP
53.5" Total Length
9.9 pounds
Brass Furniture
RE Davis Continental Flintlock
My bayonet for my Long Land Pattern musket arrived today! Loyalist Arms was great to deal with. Ordered last Monday and it arrived this afternoon. Just had to tell Blair there the measurements of my barrel and he found one to fit. Scabbard included for a good price. I'm quite pleased with it!
Attachments
Thank you RanchRoper
- Joined
- Nov 14, 2010
- Messages
- 1,207
- Reaction score
- 1,609
Sir that is absolutely beautiful.
Thank you Walt53
ernbar
45 Cal.
So finally found a Spiller & Burr, unfired from 1998 from board member parrot head, thanks! The pistol is in mint condition but the hammer pull was quite heavy. Read about hour glassing the spring so broke out the old Sears grinder and gave it a slight taper making sure the metal staid cool. The mod reduced the trigger pull to a normal one. Next came the front post replacement. It was so small that my pliers couldn’t grab it to be pulled out. I filed a small flat spot on the post and drilled it out in my drill press. The picture shows the sight pulled out on the drill bit. These pistols will shoot a foot high at 25 yards so a new post was fashioned from 1/8” brass rod turned down using a file and a drill press till I got the desired diameter size (around .119”). From what I have seen on others doing this the post should be about 1/4” high. The post can be carefully pressed back in by pounding it into the pocket.
I also added a light muzzle crown.
I also added a light muzzle crown.
Shot my 36" .45 SMR yesterday evening until it got dark. Man I love that little rifle, it is a tack driver.
Then went inside and opened the box to check over the Ron Paull rifle the mail lady delivered. 36"x13/16" slotted breech .32 caliber bbl, English styled halfstock, small siler flint, 7.0lbs. Hopefully if I can get all the important things done on the ranch today, I'll be able to make some smoke before it gets dark this evening.
Then went inside and opened the box to check over the Ron Paull rifle the mail lady delivered. 36"x13/16" slotted breech .32 caliber bbl, English styled halfstock, small siler flint, 7.0lbs. Hopefully if I can get all the important things done on the ranch today, I'll be able to make some smoke before it gets dark this evening.
Finished up another “file” knife and sheath to give to my niece as a gift. She’s an avid deer and turkey hunter. I made an “A” out of some nickel silver for her initial and inletted it. Hopefully, I’ll get it sent off this week, just in time for deer season!
Very cool. Nice looking set-up. I am certain that she will cherish it.
- Joined
- Mar 13, 2020
- Messages
- 7,492
- Reaction score
- 21,008
- Location
- On the Border in Idaho looking at BC
please uncle compressor guy, may i have another! that is one fine knife!
- Joined
- Mar 13, 2020
- Messages
- 7,492
- Reaction score
- 21,008
- Location
- On the Border in Idaho looking at BC
Tom, do you take orders or make those on order? i have a couple knives that need clothes.
