where can I buy scrimshaw tools?

[soggy]

Can anyone give me the name of a source for scrimshaw tools? I have made a few horns in the past and most recently have been working on one using Scott Sibleys book as a guide. In the book they suggest to use an X-acto knife for cutting in the design, I have done this and it works ok for the most part, but I would like to get a tool for scribing letters , I find the X-acto knife is difficult to use when the designs are not straight lines.
Any suggestions would be greatly appreciated.
Soggy :thanks:

 

[fatboy]

Well you can use just about anything sharp a large sewing needle is what I plan on useing, or a awl reshaped and pointed to a very sharp point heck you can even use a large nail reshape it and put a nice point on it . :imo: :m2c: :front:

 

[LRB]

Exacto and some others make a very short bladed tool that swivels and will turn at will. Needles and such want to follow the grain of the horn, where as a blade will cut and turn across it with little variation of the desired course. Check your local hobby supply. The blade itself is only maybe an 1/8th long and triangular, mounted in a swivel head.

 

I've used an exacto knife with a fine point to do geometric designs. There really are no special tools to do scrimshaw, other than natural talent.

Just :m2c:

 

[soggy]

There really are no special tools to do scrimshaw, other than natural talent.

:: Looks like I'm in trouble ::
Thanks for the advice fellows, I'll make a couple of different tools and see what works best for me
:thanks: Soggy

 

[brubincam]

get a dental pick from your dentist :hmm: :hmm: :hmm:

 

[Old40Rod]

get a dental pick from your dentist

Ditto checking with your dentist... I checked with mine... when I told him what I needed he took me into a back room and pulled out a cardboard box full of used picks, scrapers, etc., and said "take all you want". He only made me promise not to tell any of my BP club friends where I got them... he said something about not wanting a bunch of guys with names like "Squatting Elk" and such hanging around his office :crackup:

I told him if he would just a have look in their collective mouths he would find the money to pay for his new Ford Expedition. ::

 

[DRC]

I use a three sided carpet needle in a drafting pencil holder. I have to wrap a little tape around the needle but it works for me.

 

[Wart]

I've found that an old victrola (sp.) needle inserted into an exacto handle works the best. They are a bit hard to come by but can be found at flea markets, antique shops, etc. :imo:

 

[oldmaster]

I can't stop laughing! "Squatting Elk"? :crackup: :crackup:

 

[soggy]

:thanks: Thanks Griz; Wart, that's kinda what I was looking for , something practical that I could adapt to do the job. It's kinda rural where I live (50+ miles to the narest dental clinic ,150 to the nearest city). So if I can't buy it on line, I have to make it myself.
Soggy :front:

 

[Blkpowder]

Ok soggy check with a company out of Lodi ohio call the LOG CABIN SHOP.GO TO (logcabinshop.com)or you can call them for a catolog 330-948-4307 good luck

 

[BS]

I saw some last week, but cannot find them. Somebody has a set of shortened exato blades made for scrimshaw. I have searched and looked but cannot find them. Sorry! :hmm:

 

[scott k]

Hey soggy, this knife looks like the one in the book > log cabin Knife< I used a x-acto knife on the one I did. I would like to try something else next time. Some of the suggestions sound good. :front:
Lehigh...

 

[Tinker2]

This is what I use. carbide push button scribe. At Brownells.
http://www.brownells.com/aspx/NS/store/P...H-BUTTON+SCRIBE
Good Luck

 

[soggy]

This is what I use. carbide push button scribe. At Brownells.

:thanks: There that's exactly what I was looking for. One small problem, when I bring up that sight, it shows :
. " Dropped by Brownells"
It shows the replacement points are still available . I may call them in the morning to see if they have a substitute for this item.
In the mean time does anyone know of any other source for that scribe?
Thanks; Soggy

 

[Black Hand]

Sir,
I use a heavy needle that has been sharpened to a triangular cross-section. By turning it a little one way you can cut a line or a curve while turned a little the other way, it will scribe. Mine is set in an antler tine and doubles as a triangular awl for sewing leather. Works like a charm.
Black Hand

 

[DanWalker]

I found a carbon scribe at Home Depot.

 

[Tinker2]

I used to use a retractable drafting pencil and replaced the lead with
a steel spike made from drill rod. works well.

Good Luck

 

[Hoyt]

I saw another tool that might be good for scrimshaw and am going to get one..it's an Xacto knife..a small one that has a real small little blade that will swivel 360 degrees. Special made to cut curves and circles, etc. only takes the one blade. The little blade is about 1/8" wide where it goes into the handle. Should be good for stock inletting also.