Controversial question. Short rodding a patched ball.

L & R
Shop deals on ebay
the hawken shop
Muzzleloading Forum

Help Support Muzzleloading Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
WarDawg

WarDawg

36 Cl.
MLF Supporter
Joined
Jul 10, 2024
Messages
56
Reaction score
64
Location
Ga boy hanging out in North Carolina
I’m not asking to get folks riled up. But I have heard if you don’t get the projectile ( ball & patch ) for me , fully down the barrel you are setting it up for bad karma to your rifle. It’s nothing would do on purpose. But can happen. Watching a guy on YouTube talking about it. Where folks might push the round down with the ball starter . But forget to actually rod it any further. I know what we hear. But what is the truth in what we have seen . Some say nothing bad will happen. Some say ruined barrel. Where's the proof for either argument. Courious. Wardawg
 
So much depends on the bore diameter, the thickness of the barrel walls, the steel of the barrel and the powder charge. There have been barrels that have bulged when the ball is short started. There are a few that have catastrophically failed by splitting where the ball was short started. There are many barrels that have survived being shot when short started. A kind of cursory examination was done by two shooters (The Bevel Brothers) for a Muzzle Blasts) article for the NMLRA. Based on the rifles they tested and measured for bulging, their conclusion was that nothing bad happened to their rifles. I did have the experience of shooting a short started ball in my 1 1/8" across the flats 45 caliber rifle. There was no damage to my rifle.

This not a recommended practice. If it happens, the barrel must be inspected and not treated as if nothing bad occurred. The barrel needs to be checked for bulging. Destructive failure can occur.
 
Years ago a freind shot at a whitetail buckthatfor some reason did not immediately leave the area
In his haste to reload and get a second shot he spilled some of the powder in his quickload and added a little more without measuring then hastily rammed in a maxiball. He killed the deer but later noticeda "wallnut" in the barrel about 6" up from the breach. I belive a combination of an over load, a not fully seated maxiball and a light weight barrel a .45 Seneca ruined his gun.
 
A few years ago…..my son and I had matching Pedersoli frontier rifles, both 50 cal. We were at the range one day and shot quite a bit, he ended up short seating a ball ( ball stuck about 3”s above the charge ) dirty bore, not enough spit.
…..the ball came out just fine upon shooting but left a noticeable ring/bulge in the barrel right above the charge. 🥲

So yep, seat those balls ! 👍
 
This owner wasn't as lucky, although he sustained only minor injuries. Short started about 6 inches from the muzzle, patched ball in a smooth bore.
damaged gun.jpg
 
bpd303 said:
This owner wasn't as lucky, although he sustained only minor injuries. Short started about 6 inches from the muzzle, patched ball in a smooth bore.
View attachment 345569
Click to expand...
While this example strengthens the warning to make sure the ball is not short started, there is more information that is lacking to tell the full story. It is stated that the barrel was a smoothbore. It appears from the set triggers that this firearm started out as a rifle and the barrel was later bored out to be smooth. I would be interested to know what the size of the barrel was across the flats, what was the barrel bored out to and was this a ball or a shot load that burst the barrel. Because of the perceived modification to the barrel, I don't think that identifying the maker of the rifle is as pertinent as the other information.
 
Eric Krewson said:
I short started my .54 twice with the ball about 4" into the barrel, Rice barrel, 90 gr of 2f, .535 ball, no bulging or damage, I got lucky.
Click to expand...
Eric,
Oviously you would not have fired it had you known ahead of discharge. Since you got lucky, how did you know that the short start did occur? Was the discharge sound different?
Larry
 
Grenadier1758 said:
It is stated that the barrel was a smoothbore. It appears from the set triggers that this firearm started out as a rifle and the barrel was later bored out to be smooth. I would be interested to know what the size of the barrel was across the flats, what was the barrel bored out to and was this a ball or a shot load that burst the barrel.
Click to expand...
May not be a rebore, as TC sold quite a few 56 caliber smooth bores in Renegade stocks with double set triggers. The stock in the ‘exploded’ view appears to be a TC Hawken, which also came with a 1” atf barrel in 54 caliber, allowing the TC 56 smooth bore barrel to drop right in. Here is a photograph of a TC 56 caliber smoothbore that rests in the safe.
1725042294128.jpeg

As far as the cause of the exploded barrel a few posts back, it doesn’t look like any of the short started barrels with blackpowder loads that I save seen, though with it split from breech to muzzle, it looks very similar to photographs of barrels destroyed with that powder that doesn’t smoke, short started or not.
 
Grenadier1758 said:
@SDSmlf, I based my reply seeing the brass butt plate and brass trigger guard that the firearm was not a Renegade in 56 smooth bore. But in any event, there is a lot more to the examination of that pictured rifle than a short started ball.
Click to expand...
A closeup of what’s stamped on the barrel would be a clue, though honestly doubt there would be evidence of charcoal or sulfur residue in the bore (unless from a previous load), but without the barrel in hand to examine, just speculation.
 
Got my first ML rifle in '68 and knew almost nothing about black powder shooting other than a few general references (pre internet and no mentor). My buddy's dad had an original .36 percussion, so we headed to the range. After 4-5 shots, without swabbing, he could only push the ball about 3/4 down the bore. No problem, he just shot it out. Blew the drum out of the barrel (don't know if the barrel bulged). Lesson learned.
 
Ok. What exactly is happening for it to burst / or ring a barrel ? The distance of the powder charge and explosion from the projectile builds to much pressure vs the projectile sitting up against powder ?? While ridding the projectile up against the powder is what we want. But what is the distance of safe zone to no man’s land ? Wardawg
 
WarDawg said:
Ok. What exactly is happening for it to burst / or ring a barrel ? The distance of the powder charge and explosion from the projectile builds to much pressure vs the projectile sitting up against powder ?? While rodding the projectile up against the powder is what we want. But what is the distance of safe zone to no man’s land ? Wardawg
Click to expand...
 
Pete G said:
Sounds like a squib load, sort of a loud PFFFT!!!
Click to expand...
Did you use black powder? I did this three times to a 50 caliber that I have before I figured a way to get around it, but I use 777 as this is a percussion rifle and it did the same thing, sounded like a squib load and it didn't even hit the target. I was concerned that black powder might put different pressure on than what 777 did being that the 777 had more room to expand. I didn't think it would burn this fast because it generally takes pressure to burn any kind of smokeless powder very fast. Black powder burns about the same, in a gun or just throwed on the ground.
 

Similar threads

M
Brass Barrel Rod and Test
Replies
7
Views
678
Rudyard
R
Justin.44
Torn patches!
2
Replies
36
Views
3K
TRGRHAPY
TRGRHAPY
borealedc
Round Ball performance story and question
2 3
Replies
59
Views
6K
Gordoncourtney
G
Crawfish
Range Rod Oopsie
2
Replies
25
Views
2K
th1840
T
Sparkitoff
Turkey Hunt takes a big turn ...
Replies
9
Views
1K
Britsmoothy
Britsmoothy

Latest posts

Back
Top