What Muzzleloading Stuff Did You Do Today?

David Austin · Nov 14, 2024

David Austin said:
Still sanding the browning off the Cabela's barrel. When I bought the TC renegade I also bought the sellers supplies. Looked it over. I should take a picture. Powder horns...with 2f and 4f, cleaning jags, dryball pullers, lead pot...with lead, casting tongs for calibers I don't have. caps...11's, 204'd , flints...stuff. cleaning solvents, patches, cleaning rods, nipple wrenches, nipples to fit, range box...came with the rifle.

Took delivery of ?? caliber Jukar two pieve percussion rifle NOT CVA.

Kansas Jake · Nov 14, 2024

I epoxied a front sight to 1861 Springfield to sight it in before I solder it permanently.

Norman Brooks · Nov 14, 2024

Turned plug for horn shown.

ArmorerRoy · Nov 14, 2024

I got a new axe.

TDM · Nov 14, 2024

Did a fair amount of shooting today with my .36 SMR. It was not pretty, but you got to show the bad with the good. I had the rifle pretty well dialed in already but I wanted to tweak it for Squirrel hunting. My shooting was off, I’d swear my vision gets worse every year

. Was shooting from the bench at 25 & 35 yards. Using .350 cast RBs, .022 patches, and a 1 to 4 ratio Dawn & water lube. I had previously settled on 35 gr of Swiss 3F, but I went back to 30 gr and then up to 40 gr. Seemed like the 40 gr load was printing well so I made a couple of sight adjustments and tried shooting at the squirrel targets. I just could not see them clearly as the results show. But I’ll try again tomorrow. Was using Goex 4F for prime, zero issues with the rifle besides retightening the jaw screw a couple of times. Also had zero problems with fouling. I did swab the bore after about 15 shots but it really wasn’t necessary. The squirrels are relatively safe for now.

Kansas Jake · Nov 14, 2024

I know the feeling TDM.

WALT53 · Nov 14, 2024

TDM said:
Did a fair amount of shooting today with my .36 SMR. It was not pretty, but you got to show the bad with the good. I had the rifle pretty well dialed in already but I wanted to tweak it for Squirrel hunting. My shooting was off, I’d swear my vision gets worse every year . Was shooting from the bench at 25 & 35 yards. Using .350 cast RBs, .022 patches, and a 1 to 4 ratio Dawn & water lube. I had previously settled on 35 gr of Swiss 3F, but I went back to 30 gr and then up to 40 gr. Seemed like the 40 gr load was printing well so I made a couple of sight adjustments and tried shooting at the squirrel targets. I just could not see them clearly as the results show. But I’ll try again tomorrow. Was using Goex 4F for prime, zero issues with the rifle besides retightening the jaw screw a couple of times. Also had zero problems with fouling. I did swab the bore after about 15 shots but it really wasn’t necessary. The squirrels are relatively safe for now.

Your gonna have to bight the bullet and go with peep sights or try scare em to death .

TDM · Nov 14, 2024

WALT53 said:
Your gonna have to bight the bullet and go with peep sights or try scare em to death .

Hell Walt, I can’t even see with peep sights!

WALT53 · Nov 14, 2024

TDM said:
Hell Walt, I can’t even see with peep sights!

Well bud I have the strongest readers going and a stigmatizen in each eye and regular sights are a blur heck even the front sight on my trade gun is fuzzy at times and the barrels only 26” s .I don’t know what to tell you except maybe you best think about just using that nice new trade gun you got and forget the rest that’s what I did .Look at it this way you can probably see the front sight good enough to hit something at 50 yards and with 7/8 to 1 1/4 ounces of shot no worries .Just a suggestion my friend that’s why we shoot smoothbores so we don’t have hit the bull just hit what we’re pointing at .And that’s all we do with a smoothbore is basically point them sights don’t help much anymore for most of us cause we can’t see them plain and simple .No shame in getting old just have to improvise with age if you know what I trying to say .any way good luck .

TDM · Nov 14, 2024

Sound advice @WALT53, sound advice.

Psycho Mike · Nov 14, 2024

Received a coning tool today. I think I know what my next project will be

Loja man · Nov 15, 2024

This is the time of my families annual black powder hunt in Daniel Boone national Forest! We camp for 3 to 4 days and hunt the woods hard! Here’s my oldest son with my father in the blind last night! Then this is me brokenhearted because I’m stuck on a large drywall job! I’m also building a house for me and the family! We are blessed! Basement is just about move in ready but we’re supposed to be out of the rental by the end of the month… So no brakes for hunting with my smoke poles!!

yellowhammer · Nov 15, 2024

TDM said:
Hell Walt, I can’t even see with peep sights!

Hey TDM, try this, it's worth a try, and I got improved results with my aging eyes. Instead of installing a peep on the tang close to your eye, put a peep out on the normal rear sight position. Solder on a washer or get the TOW peep:

TDM · Nov 15, 2024

Thanks @yellowhammer. Might have to try that!

flconch53 · Nov 15, 2024

yellowhammer said:
Hey TDM, try this, it's worth a try, and I got improved results with my aging eyes. Instead of installing a peep on the tang close to your eye, put a peep out on the normal rear sight position. Solder on a washer or get the TOW peep:

View attachment 362265 View attachment 362267

FULL Buckhorn worked for me

WALT53 · Nov 15, 2024

flconch53 said:
FULL Buckhorn worked for mes

Some guys have had good luck with the partridge sight to but I think they’re not that old yet .Not that any of use are ancient just ageing gracefully.lol

RobertIN · Nov 15, 2024

yellowhammer said:
Hey TDM, try this, it's worth a try, and I got improved results with my aging eyes. Instead of installing a peep on the tang close to your eye, put a peep out on the normal rear sight position. Solder on a washer or get the TOW peep:

View attachment 362265 View attachment 362267

I have that ToW sight on my Colonial. I like it a lot.

TDM · Nov 15, 2024

Had better results today shooting my .36 SMR. I worked the load back down to 30 grains of Swiss 3F and after a couple of sight adjustments I’m happy with it. Still used the .350 cast balls, .022 linen patches, 1:4 Dawn:water lube, and Goex 4F prime. I swabbed the barrel after about 15 shots but it wasn’t too bad. I was surprised at the impact rise at 35 yards but just a slight change in point of aim took care of it. But I doubt I’ll make many shots past 25 yards on squirrels. Picked up a few patches and they were all good.

Dutch7 · Nov 15, 2024

Finished inletting a barrel and breech plug in a maple stock. Need to fit and inlet the tang, then on to the lock.

WALT53 · Nov 15, 2024

TDM said:
Had better results today shooting my .36 SMR. I worked the load back down to 30 grains of Swiss 3F and after a couple of sight adjustments I’m happy with it. Still used the .350 cast balls, .022 linen patches, 1:4 Dawn:water lube, and Goex 4F prime. I swabbed the barrel after about 15 shots but it wasn’t too bad. I was surprised at the impact rise at 35 yards but just a slight change in point of aim took care of it. But I doubt I’ll make many shots past 25 yards on squirrels. Picked up a few patches and they were all good.

Gee wiz and here I thought I was gonna inherit a 36 cal oh well better luck next time .Good shooting young fella maybe you just need shoot more hmmmm .

What Muzzleloading Stuff Did You Do Today?

Help Support Muzzleloading Forum:

36 Cl.

54 Cal.

45 Cal.

Attachments

40 Cal

Cannon

Attachments

54 Cal.

36 Cal.

Cannon

36 Cal.

Cannon

Free Cdn

54 Cal.

Attachments

45 Cal.

Cannon

50 Cal.

36 Cal.

West Harrison, Indiana

Cannon

Attachments

45 Cal.

36 Cal.

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!